×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe paper describes a design and simulation of a Supervisory Control And Data Acquisition (SCADA) system to control oil pipeline and depot plant. The aim of the process is to control oil transportation through a shared pipeline and to minimize products contamination. The study attempts to fulfill an optimal sequence of batches of refined products to satisfy the customer demands in term of: volume , maximum flow rate, optimizing the total operational cost, and reducing products contamination.The proposed system introduces a control algorithm to perform process control system functions and for achieving the tasks and actions in specific sequences and precedence. The control algorithm performs processing of pumping station control, sharing single oil pipeline, maintaining tanks level, and depot inventory control. This paper investigate many factors which effects the length of transmix segment, which enable to offer optimum solutions to reduce products contamination.LabVIEW software is used for performing various signals acquisition and monitoring, also for simulating and designing the control system strategy.
Electrospinning is a simple and highly versatile method for generating ultrathin fibers (mainly polymers) with diameters ranging from a few micrometres to tens of nanometres. This technique has attracted tremendous recent interest in both academia and industry, owing to its unique ability to produce ultrafine fibers of different materials in various fibrous assemblies. Electrospinning is a process that uses an electric potential to overcome the surface tension of a solution to produce an ultra-fine jet, which elongates, thins and solidifies as it travels through the electric field to a collector.. In this research, we studied the effect of conditions of the cabin “specifically humidity” on the diameter of nanofibers manufactured by electrospinning. We used Polyvinyl alcohol (PVA) polymeric solution with weight concentration of 10%, voltage 20 kv, under different values of relative humidity. Fiber morphology and fiber diameter were determined using scanning electron microscope, and measuring the fiber diameter by using image j program. It was found that the diameter of the fibers increased with increasing the relative humidity within our studying area .
The aim of this work is to optimize EPD variables (voltage, time, and focus) using alternating current through the Taguchi Design of Experiment (DOE). Coating Nano hydroxyapatite (Nano-HA) on a Ti6Al4V substrate depends on thickness and roughness, then characterization of a coating layer to determine the optimum state. Hydroxyapatite (HAp) powder was deposited on a Ti-6Al-4V alloy substrate by electro-deposition with ethanol as a solvent under AC current, to improve the alloy surface quality based on coating thickness and maximum coating mass meeting the requirements of a biological orthopedics application. Ethanol was used as a solvent to precipitate ketazone and HAp on the base alloy. Taguchi's approach was used in order to determine the optimal conditions for EPD and subsequently to apply various criteria for depositing the biochemical coating. The surface and cross-section composition of the paint is described by characterization. Numerous tests and inspections; Zeta, XRD and SEM stability test, water contact angle and optical microscopes were used to describe the surface morphology of the HAp layer. The value of the optimum conditions for deposition of the HAp layer which is a simultaneous thickness and maximum coating mass, was predicted at a sedimentation voltage of 40 V, 2 min sedimentation time and 1 g / L for the concentration of the suspended solution at room temperature. The validity of the model resulting from the response surface methodology was assessed by comparing the expected results with the experimental results. In addition, close agreement was observed between the experimental results and the expected results. For the solution at room temperature, the results obtained with the highest value of the coating thickness of 41at the surface roughness of 0.94 and the contact angle of the alloy before coating is 67.489º reduced to. 38.132º after plating, which indicates an increase in the harmony of the metal implant and biocompatibility.
This research focuses on enhancing the diagnostic power of the slit lamp, a fundamental ophthalmic instrument, by replacing its traditional halogen light source with a cutting-edge white laser. The objective of this modification is to significantly improve the brightness, intensity, and color accuracy, which are crucial for distinguishing fine ocular details during eye examinations. White laser technology offers a more stable, energy-efficient light source with reduced maintenance needs, making it a valuable upgrade over conventional systems. As part of this redesign, the optical system will be optimized with new filters, lenses, and heat management techniques to accommodate the white laser. Additionally, integrating a high-resolution digital camera with the enhanced illumination system is expected to provide sharper, more accurate imaging for better diagnosis. The anticipated outcome is a transformative improvement in ocular diagnostics, leading to earlier and more precise detection of eye conditions. This advancement holds promise for both patients, through better care, and ophthalmologists, through increased diagnostic efficiency. Challenges in implementation and potential solutions are also considered.
This paper provides a comprehensive overview of microfluidic device (MFD) manufacturing processes. The review starts with an introduction elucidating the significance and advantages of MFDs. Subsequently, a brief description of the materials employed in MFD fabrication is presented. The manufacturing process used to create MFDs is then thoroughly examined, with a focus on the application of laser technology.