×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this work, the vibrations in the rotor-bearing system are studied experimentally and theoretically using ANSYS Workbench 2020 R1 software to compute the natural frequencies and mode shapes. In the experimental part, the LABVIEW software was used to examine the signal of the frequency domain values obtained from the accelerometer sensors, based on Fast Fourier Transform (FFT) technology and dynamic response spectrum. in the theoretical part, the natural frequencies are determined based on the finite element method for analyzing the system and knowing its behavior and vibration response level. The results showed that the level of vibration becomes higher at high rotational speeds, and it becomes large when the distances between the bearings are large, according to the bearing position and type used in the system. in this work can be concluded, the system is usually affected by the dynamic response around it and is difficult to separate from it, and the vibrations in the system can be controlled by adding an external damping source, which gives the system more stable. A system operating at high speeds can give a large vibration and an unbalanced response.
This study concerns utilization of nonlinear finite element method for to evaluate the role of longitudinal soffit-bonded CFRP strips in elevating the shear behavior of RC beams without stirrups. All beams cross-sections were of 150 mm breadth and 200 mm depth, the overall length was 1500 mm with clear span 1300 mm. One beam was provided by minimum web reinforcement according to the ACI 318M-14, while the other five were without web reinforcement but externally strengthened by a variety of CFRP-strip combinations consisting of longitudinal soffit-bonded strips. The predictions of a proposed ANSYS (version 14.5) model for six of the test beams including modeling of concrete, steel rebars, CFRP strips and supports and loading steel plates, by SOLID65, LINK180, SHELL41 and SOLID185 elements, respectively, show high agreements with experimental evidence, which stands as a definite witness to the efficiency and reliability of the present numerical model.
The field of mechanics concerned with studying the propagation of cracks in materials is Fracture Mechanics. Technology systems are meant to withstand the loads to which they are likely to be exposed when in use. Material imperfections arising at the time of production or use of the material are, however, unavoidable and must therefore be taken into account. A stress intensity factor is a fracture parameter that defines the part failure. This paper study’s the effect of cracks on the stresses of rectangular plates having a hole in the center. The plate was subjected to tensile pressure at the top side while maintaining the bottom side fixed. The plate had four cracks distributed around the centered hole at 45o at each side. The effect of the length of the cracks on the resulted stresses and strains was investigated. Also, the effect of the position of the crack on the resulted stresses and strains was studied. Finite element models for the different plate cases were built using ANSYS software. The results showed that increasing the crack length resulted to increase the stresses and strains. The dimension of the plate width, height and thickness were 150 mm, 300 mm and 1 mm respectively, and the crack position was investigated for different crack lengths (5, 10, 15, 20, 25 mm) however the results were not steady as it looks that the crack lengths have changed the stress distribution over the plate.
In this research, experimental and analytical deep drawing of the several-stages design mold is produce hexagonal cup and also proved the influence of the thickness of the sheet on the allocation of strain and laminating in curvature of the cup area for all stages of the drawing. Three stages deep drawing mold was designed and constructed to carry out the experimental work required to produce a hexagonal cup of (28.25 mm by 24.5 mm) , (60 mm) high drawn from a circular flat sheet (80 mm diameter), made from low carbon steel (1006–AISI). Analysis program (ANSYS11.0) to perform the finite element method to accomplish the analytical side of the search. Three types of thickness sheet (tt°= 0.5, 0.7,1 mm) with constant radius of curvature of punch equal to (RRpp =4) mm, radius of curvature of die equal to (RRdd=8 mm)and radius of curvature of wall of die (RRcc= 4 mm) were used. From the experimental and analytical results of the three stages of drawing, it has been found that drawing load less than the more advanced stages of drawing operation on the wall of cup, maximum laminating take place at curvature of the cup area with sheet thickness equal to (tt°=0.5 mm) and maximum thickeningtake place at the at throat cup with sheet thickness equal to (tt°=1 mm), the maximum values of strains (radial, hoop, thickness andeffective)take place at throat cup with sheet thickness equal to (tt°=1 mm).
Pressure vessels are the heart of plants and oil refineries stations. In many engineering applications such vessels can be subjected to periodic loading either internally due to the charging and discharging process or externally due to the excitation from other nearby components such as pumps, compressors or from seismic. So that in spite of a good design according static assumption it may be critical in dynamics. In this work a horizontal pressure vessel with accessories subjected to liquefied petroleum gas pressure LPG is considered. Three models of different head types are investigated herein namely; Deep torispherical, Elliptical 2:1 and Hemispherical. The design and material selections are chosen as per ASME. For practical service many accessories are attached to the vessel such as manhole, supports, inlet and outlet opining. Finite Element method via ANSYS R18.2 is introduced for the numerical analysis. The fatigue life in case of fully reversed cyclic loading are estimated and located. Vibration characteristics such as mode shapes and natural frequencies for the lowest five modes are evaluated and compared. It is found that the fatigue life can be increased as higher as 180% for hemi- spherical head as compared with deep torispherical head pressure vessel and the lowest four natural frequencies are nearly identical for all models, however significant change observed in the fifth natural frequency.
A dam failure results in losses in terms of economy and infrastructure, in addition to the loss of many lives and assets. Inadequate seepage control procedures are typically the cause of seepage failure in earth-fill dams. For an earthen dam to be waterproof and to minimize seepage, non-homogeneous dams with a clay core are one kind of embankment dam used. As water moves through the dam's core, friction causes it to lose a lot of energy. Both vertical and inclined cores can be used in the design and construction of zoned embankment dams. As a result, choosing the proper materials and dimensions for the earth dam's core is critical. The main objective of this study is to investigate different seepage control strategies for an earth dam (HORAN DAM) using the Finite Element Method (FEM). We modeled and analyzed nine cases of various seepage control techniques that have been modeled and analyzed using SEEP/W, a FEM-based software. The modeling results show using chimney filters reduces pore water pressure more effectively than using toe rock and horizontal filters. Regarding seepage, trapezoidal cores perform better than inclined cores, and the milder slope is preferred over steeper core slopes. The results show when the core permeability decreases, the seepage quantity also decreases. Toe rock decreases seepage more than horizontal filters and chimney filters. Additionally, it has been shown that using a toe rock filter together with a trapezoidal core with a mild slope performs better than using a different filter and a different internal clay core shape.
In this paper, a dynamic analysis has been carried out on zoned earthdam subjected to earthquake excitation in which pore water pressure, effective stresses and displacements are calculated. The finite element method is used and the computer program Geo-Studio is adopted in the analysis through its sub-programs SEEP/W and QUAKE/W. A case study is considered to be Khassa Chai dam which is located on Khassa Chai river north of Iraq and consists of zoned embankment with a total length of 3.34 km. The selected earthquake for the analysis is El-Centro earthquake with a period of 10 sec and different amplitudes of acceleration. The time of the analysis is taken as 600 sec. with a time step (?t = 0.05 sec.) to investigate the behavior of the soil for a period of time after the earthquake has stopped, a free vibration period is included in the analysis. It was concluded that the value of pore water pressure generated at the base of the core is greater than that in the upper parts of dam. The horizontal and vertical effective stresses continue to decrease during the period of analysis 600 sec. which indicates that the soil continues to weaken during this period, the horizontal displacement increases with depth of the point from the crest and the largest horizontal displacement will be at the base of the dam at time 60 sec and There is attenuation of the acceleration to some degree depending on the amplitude of the input horizontal acceleration. The maximum horizontal displacement decreases by about 37%, 45% and 49% when using a horizontal drain 2 m thick at the downstream under a peak acceleration of 0.05g, 0.1g and 0.2g, respectively.
One of the unique properties of laser heating applications is its powerful ability for precise pouring of energy on the needed regions in heat treatment applications. The rapid rise in temperature at the irradiated region produces a high temperature gradient, which contributes in phase metallurgical changes, inside the volume of the irradiated material. This article presents a comprehensive numerical work for a model based on experimentally laser heated AISI 1110 steel samples. The numerical investigation is based on the finite element method (FEM) taking in consideration the temperature dependent material properties to predict the temperature distribution within the irradiated material volume. The finite element analysis (FEA) was carried out using the APDL scripting language (ANSYS Parametric Design Language) that is provided by the commercial code ANSYS. Infrared (IR) thermography technique was used to explore the workpiece surface and to validate the obtained results. The work takes into account the effect of different speeds of the laser beam and pulses overlap on the temperature pattern of the material surface and depth.
Shear walls are effective structural elements used mainly in multi-story buildings to provide resistance against lateral loadings such as earthquake and wind loadings. There are several types and shapes of shear walls depending mainly on geometry and height of the building. Both type and shape of the shear wall affect the efficiency of resisting lateral loadings. In this study, fifty six building models have been analyzed using the finite element method by using the SAP2000 V14 computer program. Each model have ten stories, subjected to earthquake loadings, with various numbers of bays, and with three types of shear walls, namely: side shear walls, middle shear core, and double shear cores, provided that each type of the shear walls (or cores) has the same material volume. The analysis outputs have been investigated to select the appropriate type and location of the shear walls (or cores) for the multi-story buildings subjected to earthquake loadings. Specified conclusions have been presented to obtain the optimum behavior for the multi-story buildings under the effects of earthquake loadings.
The traditional electric poles in Iraq are usually made from steel materials. Such materials induced high weight, corrosion, permanent deformation caused by high wind speed, etc. The study aimed to numerically examine the strength of few poles made from different materials. The pole subjected to pressure developed by actual measured wind speed of 140 km/h. The numerical model of different materials and cross sections, an octagonal section electric pole made from composite material FRP–HDPE–FRP is suggested to replace the traditional one. The results showed high safety factor, approximately 5.51 besides the low ratio of high strength to weight as compared to steel materials. Using HDPE as reinforced material resulted in pole elastically deformed with only 0.222 mm. Therefore, it can be assumed that the suggested pole acts partially as a damper. Straight octagonal cross - section of pole promoted high reduction (74.22%) in maximum Von–Misses stress of that obtained in cylindrical three-stage pole. High reduction (5.87 times) in maximum deformation value was obtained when composite octagonal pole was used as compare to tapered pole made from steel.
The finite element method is one of the important methods in analyzing geotechnical engineering problems; its main advantage is the ability to apply for the materials exhibiting non-linear stress-strain behavior. In this study the finite element program PLAXIS 3D 2013 is used to study the behavior of the piles under the influence of seismic waves in saturated sandy soil and the effect of adding geogrid with the pile foundation. The program has been used to facilitate the representation of the real model, input the required soil parameters and implementation of seismic data. Seismic wave, the soil geometry and the pile dimensions were fixed in all models, while dimension and depth of the geogrid used were varied to study the influence of different depth and dimension in reducing the pile displacements and the pore water pressure of soil. The results show that The reduction in settlement ratio (the difference between settlement of pile without and with using geogrid to the settlement without using geogrid) for ( ×L/2), (L×L) and (2L×2L) are 10.6%, 17% and 21.3% respectively. And the settlement ratio for geogrid at depths 8.33% and 12.5% of pile length are 9.6% and 17% respectively.
This paper deals with the elastic stability of a column bolted at its mid-height to a simply supported square plate and subjected to a concentrated load, using energy method. A uniform homogeneous column is assumed to be pinned at both ends. From symmetry considerations, half of the column is modeled by making the plate acting as a torsion spring on the column at its mid-height. The column length and cross-section, plate dimensions and thickness, and the material properties for the column and the plate catch the interest of the author. The problem is solved by using energy method and ultimately, the elastic buckling load is found. The analytical elastic buckling load is compared with a numerical solution obtained from finite element method using SAP2000. The numerical results agree with the analytical solution. The finite element model is refined to catch the actual effect of the bolted plate on the elastic buckling load. It has been found that the elastic buckling load is increased due to the increase in the rotational stiffness provided from the plate.
One of the health issues that many people encounter on a daily basis is bone fracture, which can happen for a number of reasons, such as arthritis, sprains, or external trauma . The patient experiences instability as a result of these issues . Internal fixation is a type of surgery used to support and mend a damaged bone Treatment options include ankle joint fixation, a surgical procedure employing pins, plates, rods, or screws. This study uses gait analysis methods to assess lower limb biomechanics . Gait analysis is vital for understanding walking patterns and intervention effectiveness. The impact of different shoe designs on ankle mechanics, using the finite element method and ANSYS, is investigated The results of the EMG and the GRF were discussed._x000D_ This research deepens our understanding of lower limb biomechanics and ankle joint health. By evaluating stress effects and designing custom shoes, it enhances ankle injury treatment and management strategies._x000D_ The patient, a 70-year-old woman with an internal fixation on her ankle joint, underwent a CT scan of her ankle. The patient underwent a number of experiments to evaluate her stability. EMG was used to determine the muscle stress for a brief period of time, and ground reaction force was then used to determine the pressure of walking. Both EMG and GRF have two walking speeds of1.5and 2 km/h while wearing four different types of shoes. The behavior of the EMG demonstrates that the stress on the muscle increases as walking speed increases, and the results varies depending on the shoe. The patient is afraid to apply pressure to the injured foot, so the health foot has better pressure over the entire foot_x000D_
The human body poses the most important aim for many researchers. In nowadays, the science complex required the involvement of many resources and the coordinated team work of doctors, engineers, and other from the specialists. In the case of dental medicine, due to the nature of teeth material, their dimension and geometrical position, very important problems, like cavities that led to tooth losses. In this study, both the Experimental methods as well as the numerical finite element method have been used to analyze the stress within human teeth under forces similar to those that usually occur during chewing process with different type of food in experimental work. It was manufactured a device Resembling chewing process with vertical movement by converting circular movement into reciprocating. And used DAQ system (strain gauge sensor, DAQ and LABVIEW program) to measure the stress and strain resulted from tooth during the mastication process. Models of Natural lower first molars teeth were collected. All the teeth were cleaned from the soft tissue and stored in saline at room temperature. The teeth were randomly divided into two experimental groups according to the treated cavities shape (class I and class II) each class restored with two type of dental fillings material (Nanohybrid composite and Microhybrid composite), and then strain gauge was bonded at a buccal surface of tooth used. Their installed in acrylic jaws and applied different vertical loads. With used various morsels with different elastic modulus. The stress was calculated at the crown. In numerical 2D model of teeth were created by software Auto CAD (V.14) using wheeler 's data were transfer to ANSYS mechanical APDL (V. 16), subjected load at model similar at that applied at the Experimental work. Class I exhibited the highest stresses compared with class II, in two case Nanohybrid bear stress higher than microhybrid composite. At class I the stress at Nanohybrid is higher than Microhybrid for all morsels by rate (12.96%, 21.48%, 41.8%, 16.56%, 16.86% and 15.74%) at (E1, E2, E3, E4, E5 and E6) respectively, and the stress at Nanohybrid is higher than Microhybrid by almost (36.67%, 45.69%, 47.89%, 34.21%, 41.2% and 165.01%) respectively at the same morsels used at class II. _x000D_ Keywords: , , .