×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerMoisture-induced damage in asphalt pavements, is defined by adhesive failure at the binder-aggregate interface and decreased mechanical integrity, severely reduce pavement durability. The research examines the mechanical properties and moisture sensitivity of hot mix asphalt (HMA) enhanced with styrene-butadiene-styrene (SBS) polymer and including reclaimed asphalt pavement (RAP). Laboratory assessments, including indirect tensile strength (ITS) and tensile strength ratio (TSR) tests, were performed on conventional HMA, SBS-modified HMA (4% SBS), and SBS-modified HMA contained 20% RAP. The results indicated that SBS modification significantly improved mechanical and moisture resistance properties, where unconditioned ITS specimens increased by 37.1% and TSR value enhanced by 13.5%. The incorporation of RAP decreased ITS value by about 21 % relative to pure SBS-modified HMA; nevertheless, the SBS+RAP combination still show higher ITS and TSR values than conventional HMA.
Open-graded-fraction-course (OGFC), is a hot asphalt mixture usually utilized as a private purpose wearing course, because of open graded asphalt mixture and aggregates skeleton (stone-on-stone) contact, it contain a relatively high air voids’ percentage, after compaction which are permeable to water. In this research one type of gradation was used (12.5 mm) NMAS, to preparing the OGFC asphalt mixtures, penetration grade 40/50, crushed aggregate, asphalt content prepared with 4 % and up to 6 % by weight of mixture with 0.5 % increments. Optimum asphalt content (OAC) was selected based on these criteria, air voids content, asphalt draindown, permeability, and abrasion resistance (aged and un-aged) condition. The mix performance had been investigated by indirect tensile strength and moisture susceptibility (sensitivity) measured according to the (AASHTO T283-14). Results illustrate that the increasing of asphalt binder content leads to a decrease of the air voids content, abrasion loss and permeability values, while draindown increase, conversely, the indirect tensile strength (ITS) had been significantly increased for both conditions and this is a gaod suggestion to resistance alongside moisture susceptibility. It can be decided that the increasing of asphalt binder percent in OGFC asphalt mixture, leads to an increase in the thickness of binder coating around the aggregates. On the other hand, the influence of modifier that prepared with 4% styrene-butadiene-styrene (SBS) on OGFC asphalt mixture tends to improve the mix properties and exhibit higher (TSR) as compared with original asphalt by (31, 27.7 and 24.4) % at asphalt percent (4.8, 5.3 and 5.8) %, respectively. The SBS improved the adhesion between aggregate and asphalt which leads to reduce stripping of HMA, horizontal deformation, and increased the tensile stiffness modulus value.
This paper focused on evaluating the effect of aggregate gradation and polymer modification on indirect tensile strength (ITS) and the static stiffness for hot asphalt mixtures. In particular, data from ITS tests have been processed to obtain stiffness measurements through the application of Hondros theory. The results showed that fine mixtures had a better tensile strength by 26.3% than the coarse mixtures. The effect of compaction also was examined, the results showed that samples compacted with the Superpave gyratory compactor (SGC) had an enhancement in ITS by 36.58 and 23.1% in comparison with Marshall and roller compactor respectively. Polymer modifiers were used to estimate their effect on tensile strength, adding 4, 6, and 8% of Styrene-Butadiene-Styrene (SBS), which can rise the ITS by 3.2,6.14 and 13.3% of the non-modified asphalt mixture. Furthermore, using 4, 6, and 8 percent of SBS could increase static stiffness by 53.9, 209.6, and 302.4% respectively for roller compacted fine mixes and 58, 220, and 379.3% for SGC compacted mixes. Furthermore, SBS raised the stiffness modulus by 52.3, 188, and 295% for Marshall compacted mixes. Using hybrid modifier can improve the stiffness of the asphalt mixture. However, The results indicate that using 1, 2 and 3% polyvinyl chloride (PVC) can magnify the stiffness of mixtures by 41.2, 199.8% and 262.6 for roller compacted mixtures and 133.4, 212.1 and 354% for SGC compacted mixtures, whereas there is a stringent increasing by 133.4, 189.2 and 354% for Marshall compacted mixes. Otherwise, polymer-modification can decrease the fracturing index for coarse and fine mixtures.
Utilization of additives can be an effective way to improve the durability and performance of HMA, making them more resistant to Moisture and deformation. Plus, they can reduce the need for maintenance and repairs, saving you time and money in the long run. In this study, CKD was used in place of limestone as a filler in the asphalt mixture in proportions of 0%, 25%, 50%, 75%, and 100%, and polymer SBS 4%by weight of asphalt. According to the findings, replacement-content CKD had the highest asphalt content. When the CKD is between 25% and 50%, Stability, Flow, and Indirect Tensile Strength are improved, while the density of the asphalt mixture decreases and the amount of air voids increases at higher ratios. While SBS leads to an increase in the hardness of the adhesives. As a consequence, the stability of the SBS-containing mixes resulted in higher values than the control and additive-containing mixtures (CKD), as well as a decrease in the number of air voids. According to the results, CKD should not constitute more than half of the filler weight in the asphalt mixture.
Open graded asphalt mixture is becoming more widespread where it is applied for various purposes, e.g. drainage of rainwater effectivity, traffic safety (high skid resistance), and controlling pollution noise. However, it has many other disadvantages, of which low stability, high stripping, and moisture sensitivity. The research aims to study the effect of styrene butadiene styrene SBS addition on the volumetric and mechanical properties of open graded mixture. In this research one type of aggregate with gradation (12.5 mm NMAS), asphalt of penetration grade (40/50), and cement as filler were used. Optimum asphalt content was selected based on the criteria of air voids content, asphalt drain down, permeability, and abrasion resistance (for aged and un-aged) samples. Other properties of open-graded mixtures, such as indirect tensile strength (ITS), moisture susceptibility, Marshall stability and flow were evaluated. The results show that addition of polymer (SBS) leads to an enhancement in the properties of the modified mixtures. There is an improvement in Marshall parameters. Also, a slight decreasing is noticed for permeability and air voids. For Cantabro abrasion loss (aging and un-aging condition), the abrasion resistance is increased, the drain down of asphalt is decreased from original mixture by addition of SBS. Finally, the moisture sensitivity is improved indicating that modified mixes becomes more resistant to water damage.