×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe objective of this study is determining the mixing and compaction temperature of the modified asphalt mixture. Results of binder tests showed that the addition of 3% SBS to control asphalt (PG 64-16) would achieve the desired performance level (PG 76-16) a performance grade that fits our climate with traffic loads. When using 5% SBS the performance grade of binder increased three grades (PG 82-16) and when increasing SBS content to 8% the performance grade increased four grades (PG 88-16). At shear rate of 500 (s-1), the modified asphalt viscosity can be obtained at different temperatures and the viscosity temperature curve can be achieved. As a result, the mixing and compaction temperature of modified asphalt can be determined to reach 0.17 ± 0.02 Pa.s and 0.28 ± 0.03 Pa.s for mixing and compaction, respectively. It is noted that SBS modified reached a viscosity of 3 Pa.s when 8 % additive. Additive contents above these values may not be suitable for good workability and pump ability according to Superpave specifications. While addition of 5% SBS with control asphalt, more than 3.7times at 135°C Increase the viscosity. Marshall Stability test indicated that the strength for the SBS specimens increases as compared to the conventional specimens. An increase of about 39%, 74%, 102%, was observed with 3%SBS 5%SBS 8%SBS modified binders, respectively. The Marshall test results for 8%SBS binders required compaction temperatures above 175°C need to keep up quality of HMA item while limiting natural effect amid development, these proposals are unsatisfactory Modified mixtures the 5% SBS modification was determined to be the maximum useful content. The Superpave method to estimate mixing and compaction temperatures show are not practical for use with modified binders. Also, it is observed that good agreement values between the average Marshall compaction temperature and the High Shear Viscosity Method (HSRV) and lower than Superpave methods Where the decline ranges from 15 ºC to 17 ºC.
In Iraq some pavements of the newly constructed highway appear precocious distresses with unfavorable implications especially on the safety and the frugality. Cracking and permanent deformation are main types of these failures. The filler is doubtful to be a master contributor to these failures where its content has a significance effect on the mixture stiffness, and thereby affect the HMA pavement performance. The main objective of this research is to appreciate the influence of different contents of filler on the volumetric properties of asphaltic mixtures thus performance of asphalt mixtures through Comparative Evaluation between conventional Marshall Method and Super pave system. The implementation of a detailed experimental work is carried out to achieve the study objectives through the preparation of asphalt concrete samples using aggregate from Al-Nebaie quarry, (40-50) asphalt cement from Dourah refinery and limestone dust filler with four different contents of (0%, 4%, 8%, and 12%) by weight of the total aggregate. The volumetric properties for each mix design method are evaluated using Marshall Test and the Super pave Gyratory Compacter. The influence of filler contents on the rendering of these mixtures was evaluated.
The objective of this paper is find the effect of using iron oxide as a filler on the Marshall stability, flow and the volumetric properties of HMA and compared the results with conventional HMA using limestone dust. Three blends were used: coarse, mid and fine with neat bitumen (AC 40-50). One aggregate type (crushed) with two types of fillers: limestone and iron oxide III (?- ) with three different filler content 6%, 8% and 10%. The Marshall mix design was conducted on the three blends and the optimum binder content is computed for each blend. The Marshall stability test results and the volumetric properties analysis showed that increasing the iron oxide content from 6% to 10% increases the stability about 28%, 17% , 16% for the coarse , mid and fine mixtures respectively. This increment in stability of mixtures using iron oxide related to the increment in specific gravity of the mix (Gmb) by (1.3% to 1.5% about 30 to 50 kg/m3). On the other hand, the flow of mixtures is decreased about (5%) for mixes using iron oxide than the ones that used limestone as filler. The fine blend with 10% iron oxide exhibit the highest stability of 13.3 kN. While the coarse blend stability was 10 kN for the same filler type and content. Generally, the Marshall Test results of HMA using iron oxide as filler showed better resistance to plastic deformation, also produce denser HMA with higher stiffness. On the other hand, the volumetric properties analysis showed lesser values as compared with conventional mixture where the void in mineral aggregates and void filled with asphalt has decreased but within the acceptable limits.
The main objective of this study is to design the asphalt pavement structure for the Alkut-Mayssan highway in Iraq as a case study by using PCASE application to determine the necessary thickness of CR-modified asphaltic layers. Additionally, Marshall tests were used to investigate the effect of the dry process crumb rubber modifier on the thickness of the binder coarse layer based on various variables, such as the crumb rubber modifier with different content (1, 2, 3, 4, 5)% and sizes (0.3mm, 2.36mm , 4.75mm, and mix gradation). The test results show that while pavement thickness reduced as crumb rubber gradation increases, MR values increase. Additionally, as compared to the control mixture, the addition of 1% of CR in various gradations could decrease the thickness of the asphalt binder layer.