×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe present investigation looked at whether the Bailey approach to aggregate gradation could be used to construct Superpave HMA blends. It also looked at how this approach influenced the rutting performance associated with these mixes and compared it to mixes of asphalt created by Superpave gradations. The current research included four aggregate gradations: both fine and coarse gradations for the Superpave and Bailey gradation procedures. The repeated loading test was utilized to assess the rutting performance. The findings indicated that temperature, stress level, and aggregate gradation all had a significant impact on rutting performance. In contrast to the other three gradations, the third mixture gradation exhibited the least amount of non-reversible deformation. It translates to pavement that is more resistant to rutting and less susceptible to it.
Rutting is considered as the most generated distress in Iraqi roads as a result of the high temperature and excessive traffic load. So, it is essential to utilize polymer modified binder to increase the performance of pavements. The objective of this paper is to assess the effect of aggregate gradation and filler content on the rutting formation of Colored Hot Mix Asphalt CHMA. The HMA was colored by using iron oxide as filler to produce red HMA. Two blends were used: fine and coarse with two different types of filler iron oxide for CHMA and limestone for conventional HMA with two filler content 6% and 10%. Neat (AC 40-50) and modified asphalt (AC 40-50 + 4%SBS) were used. Tests are held on adding 4% Styrene Butadiene Styrene )SBS( by the weight of neat asphalt (AC 40-50) to raise the performance grade by two grades from PG (64-16) to PG (76-16) [1] and [2]. The wheel tracking test is used to assess the rut depth of the CHMA. The test results showed that the using iron oxide with neat asphalt increase the rut depth resistance by 200 and 400 failure load cycles than mixtures using limestone (cycles that mix reach 25 mm rut depth) for fine and coarse mix respectively. Also, the effect of gradation shows that the fine mixture fails at 4000 cycles while the coarse mixture fails at 1800 cycles for 6% limestone mixtures. Increasing the iron oxide content from 6% to 10% leads to increase the failure load cycles by 2200 and 1200 cycles for fine and coarse mixture respectively using modified asphalt. The fine mixture with 10% iron oxide using modified asphalt gives the best performance with 7000 cycles than the coarse mixture with 10% filler content and modified asphalt with 4000 cycles. irrespective the filler and type of binder, the dense mixtures using iron oxide as filler exhibit better resistance to rutting formation than coarse mixtures.
Rutting is the most common distress that most Iraqi asphalt pavements suffer from it. Asphalt binders are modified by using additives and polymers to enhance their physical qualities and fulfill the performance demands. Polyphosphoric acid (PPA) has been used in many countries to enhance the physical and mechanical characteristics of asphalt binders and mixtures that can improve the performance of asphalt pavements. In this paper, evaluation of the Iraqi asphalt binder and mixtures performance by using three percentages of Polyphosphoric acid (PPA) (0.4, 0.8, and 1.2) percent by asphalt binder weight and added to (60-70) penetration grade asphalt binder to show the applicability and suitability of using PPA in asphalt pavement in Iraq. Original asphalt binder and modified are subjected to traditional tests which are penetration, ductility, softening point, and viscosity. Results show better performance and enhancement of the physical properties of the modified binder. Other tests are Marshall Stability and wheel track tests. The results of the addition of PPA to the asphalt mixture show increases in the Marshall Stability and enhance the performance of the asphalt pavement mixtures. The wheel track test is applied to the original and modified mixture at two test temperatures 40 ?C and 50 ?C and the results show a decrease in the rut depth when the percentages of PPA increase. It is concluded that %PPA addition will enhance the performance of the Iraqi asphalt pavement and the mixture will be more rutting resistant, especially in high-temperature weather.
Reclaimed (recycled) asphalt pavement (RAP), the most recycled material worldwide, is the mostly reclaimed material utilized in hot mix asphalt. Polymer (Crumb rubber) incorporation frequently leads to enhanced durability and resistance to heat cracking and rutting, two forms of permanent deformation. It also relieves stiffness and minimizes fatigue damage. This study aims to gather all previous RAP-related research and crumb rubber CR, so that the impact of using these materials on mechanical, physical properties of asphalt pavement, environmental effect and cost effective are clarify and explained. The finding of this research proved that the use of RAP and CR provide considerable structural and financial enhancements to the construction.
The objective of this paper is find the effect of using iron oxide as a filler on the Marshall stability, flow and the volumetric properties of HMA and compared the results with conventional HMA using limestone dust. Three blends were used: coarse, mid and fine with neat bitumen (AC 40-50). One aggregate type (crushed) with two types of fillers: limestone and iron oxide III (?- ) with three different filler content 6%, 8% and 10%. The Marshall mix design was conducted on the three blends and the optimum binder content is computed for each blend. The Marshall stability test results and the volumetric properties analysis showed that increasing the iron oxide content from 6% to 10% increases the stability about 28%, 17% , 16% for the coarse , mid and fine mixtures respectively. This increment in stability of mixtures using iron oxide related to the increment in specific gravity of the mix (Gmb) by (1.3% to 1.5% about 30 to 50 kg/m3). On the other hand, the flow of mixtures is decreased about (5%) for mixes using iron oxide than the ones that used limestone as filler. The fine blend with 10% iron oxide exhibit the highest stability of 13.3 kN. While the coarse blend stability was 10 kN for the same filler type and content. Generally, the Marshall Test results of HMA using iron oxide as filler showed better resistance to plastic deformation, also produce denser HMA with higher stiffness. On the other hand, the volumetric properties analysis showed lesser values as compared with conventional mixture where the void in mineral aggregates and void filled with asphalt has decreased but within the acceptable limits.