×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe main objective of the present paper is to investigate the effect of fineness moduli (FM) of fine aggregate on fresh properties (flow ability. Passing ability and segregation resistance), and hardened properties (compressive strength, split tensile strength, flexural strength and ultrasonic pulse velocity UPV) of self-compacting concrete (SCC). Four values of FM 2.3, 2.5, 2.7 and 3.1 were used, according to acceptance range of ASTM C33-03 for FM for fine aggregate, which recommended range for FM is 2.3 to 3.1._x000D_ Four series of mixes were casting , each series consist of two mixes represent normal strength and high strength SCC, each series of mixes made from fine aggregate have the same FM. Flow ability, passing ability.and segregation resistance of fresh SCC, both with normal and high strength decreases with increasing the fineness moduli. High strength SCC more effected than normal strength concrete due to increase the volume of particles. _x000D_ Great enhancement in compressive strength split tensile strength and flexural strength in both normal and high strength SCC when the FM is 2.5. Increase FM to 2.7 and 3.1 not lead to increase in strengths. The UPV values of normal and high strength SCC mixes have a good general condition. SCC mixes with FM 2.5 possess excellent general conditions.
This research was conducted to investigate the effect of using internal steel plates for shear reinforcement on flexural behavior of SCC beams instead of using traditional reinforcement bars (stirrups) and to study the effect of their spacing and thickness on strength. The experimental work included destructive tests on six SCC beams under two-point load. The results showed that the yield loads in all of the beams with steel plates were lower than the reference beam by (5.21%) on average, the deflection at yield load was higher by (13.72%) on average and the ultimate loads were lower by (6.77%) on average except in one beam where it was higher by (0.37%). It was also found that the ultimate deflection in beams with internal shear steel plates was lower by (10.01%) on average except in the aforementioned beam where it was higher by (2.31%). Ductility in all beams with steel plates was lower by (20.08%) on average and the strain before a load of (200kN) was higher in the longitudinal reinforcement and lower in shear steel plates and vice versa after a load of (200kN). Theoretical analysis was also carried out for all beams using the finite element program ANSYS (version 15) where theoretical results of load versus mid-span deflection relations, longitudinal reinforcement strain, shear reinforcement strain, variations of neutral axis depths and cracks patterns showed good agreement with experimental ones. Finally, some specific further studies were recommended.
Construction joints are separations between successive concrete pours. They are critical in the building of large concrete structures, since these structures cannot be cast in a single pour. Self-consolidation concrete is a relatively new kind of concrete that is considered suitable for a wide range of construction applications, especially those needing a high early resistance. Certain findings from earlier experimental tests were adopted and analyzed using finite element analysis. ANSYS program was used to analyze the impact of utilizing high strength concrete (fc') and the secondary reinforcement ratio (ρv) on the behavior of reinforced self-consolidating concrete beams having a horizontal construction joint. Nine beams analyzed in this study have the same dimensions (150×180×1200) mm (width× height ×length). Between the two supports, the clear span was 1100 mm. Two-point loads were applied to the simply supported beams during testing. One of the beams acts as a control beam (without a construction joint) and the remaining beams were with horizontal construction joint in the tension zone. The ultimate loads obtained analytically vary by between 3.1% and 7.8 % from those found experimentally. The presence of the horizontal construction joints made the beam less stiff. Utilizing a 70 MPa high strength concrete resulted in a 47.4 % in ultimate load over the experimental value for regular strength concrete (28 MPa). Increasing the ratio of secondary reinforcement (0.01229 to 0.049) resulted in a 10.3% increase in ultimate load magnitude, while decreasing the ratio of secondary reinforcement (0.01229 to 0.0025) with spanning the spacing between stirrups led to a reduction in ultimate load magnitude by 55.8%.