×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerBoth surface extension and nanofluid methods were used to enhance the heat transfer in a double pipe heat exchanger under turbulent flow conditions. Aluminum oxide nanoparticles were used with different concentrations(0.6-3 g/l)in hot water to increase the heat transfer rate on smooth tube and circular fins tube for a range of Reynolds number4240-19790. The simulation was also performed to predict the heat transfer coefficient and temperature profile for selected conditions in which COMSOL Multiphysics is used. The experimental results revealed that the heat transfer enhancement by both circular fin and nanofluid exhibited an increasing trend with Reynolds number and nanofluid concentration. The conjoint effect of Al2O3 of 3 g/l concentration and circular fin provided largest heat transfer enhancement of 53% for the highest Re investigated. Simulation results showed reasonable agreement with the experimental values of heat transfer coefficient. The simulation showed that the presence of nanofluid on finned surface influenced the temperature profile indicating the increased heat transfer rate.
Non-dispersive near-infrared technique is widely used nowadays for the detection of gases, especially in harsh environments. In this study, an optical gas cell was designed for oxygenator exhaust capnometry. A computer-based simulation was used for the analysis of air flows for model selection. ANSYS Discovery 2020 R2 was used for model simulation. The gas flow cells were tested using a custom-made gas rig to measure the fraction absorbance of carbon dioxide gas at the detector. Two gases were used, nitrogen gas as a reference gas (0%) and 9% carbon dioxide. Three gas cells with the following optical path lengths were tested: 31mm, 36mm, and 40mm. The results showed that all gas flow cells produced laminar flow and small pressure drop across the inlet and outlet of the cell (11~12 Pa). Further, the minimum velocity is obtained in the 40mm gas flow sensor and it is located at the gas outlet path away from the effective optical gas path. The simulation and experimental results indicate that the gas flow cell of 40mm optical path length is more suitable for the intended application as it offers a maximum effective absorption path compared to the stagnation areas, and as a result, it provides the maximum fraction absorbance.
The solar vortex engine (SVE) has been investigated to generate power using renewable energy. The SVE was constructed from a vortex generation engine (VGE) and solar air collector (SAC). The SVE system primarily utilizes vertical air movement. However, the airflow entering the VGE experiences an obstruction. The purpose of this paper is to propose a new design for the VGE that creates a swirling updraft capable of overcoming air obstruction and reducing energy losses. A 3D numerical model of VGE was developed to visualize vortex generation. The modeling of the VGE is carried using SOLIDWORKS software and ANSYS-FLUENT 18. The improved VGE has six vertical twisted convergence blades connected to six guide vanes to direct updraft air in an anticlockwise swirl. All blades and vanes are housed in a VGE cylinder with a diameter of 20cm and a height of 30cm. The simulation results were validated by comparing with the results obtained from the present experimental model. The simulation results match with a mean difference of less than 5% with the experimental measurements. The results of the current CFD investigation indicate that there is a gradient in air temperature and pressure within the VGE, ranging from the highest values of 314 K and 3.85 Pa to the lowest values of 308 K and 2.42 Pa, respectively. The CFD visualization shows a threefold increase in axial velocity and a fivefold increase in tangential velocity within an artificial vortex. Therefore, it can be concluded that the new VGE construction is highly efficient in generating a vortex.
Continuous Positive Airway Pressure (CPAP) ventilation remains a mainstay treatment for different respiratory disorders. Good pressure stability and pressure reduction during exhalation are of major importance condition to ensure the clinical efficacy and comfort of CPAP therapy. Obstructive Sleep Apnea (OSA) and today coronavirus (COVID-19) are the main two diseases mitigated by the CPAP. This paper introduced a systematic review of the CPAP design in terms of the hardware design, Simulation-based CPAP system, control algorithm, and the measured performance. The accuracy is used as measurement of performance and calculated from the pressure value. The accuracy was compared to the predefined U.S. Food and Drug Administration (FDA)-based threshold value in which it considers this value as a reference. The results related to the modern CPAP devices introduced in this study to explain the accuracy of experimental CPAP. These were compared with a commercial CPAP devices. Also, it was revealed how the results coincide with the error ratio defined by the FDA as an evaluation measurement. The FDA error ratio determines the performance of the optimized CPAP device. This work is the first review that presented the knowledge about engineering design of the CPAP system, so it will be the first in the literature.
This paper introduce a new way to simulate the effect of changing the length and the band gap of the nanotube on the current of carbon nanotube field effect transistors (CNTFET( by using simulation tools: FETToy, CNTFET lab, CNT bands 2.0, since this simulation were done in different parameters of ZigZag nanotube. We use three simulations tools because each tool provides simulation of parameters that differ from the parameters of other tools, so we can study more parameters that we change which this article is studied._x000D_ In this paper we studied the effect of changing of ZigZag nanotube length which has a chirality (n,0) on the current of the CNTFET. We have found that the relationship between nanotube length and the current of the CNTFET is an inverse proportional, as the nanotube length increase, the current of CNTFET decrease, and the relation between the band gap of the ZigZag nanotube and current of the CNTFET has been studied too. We have found that this relationship is an inverse proportional, as the band gap increase, the current of CNTFET decrease. Also, we studied the relation between the band gap of the ZigZag nanotube and the average velocity of charges in CNTFET, we found that relationship is an inverse proportional, as the band gap increase, the average velocity of charges of CNTFET decrease.
As internet network developed rapidly in the past ten years, and its operating environment is constantly changing along with the development of computer and communication technology, the congestion problem has become more and more serious. Since TCP is the primary protocol for transport layers on the internet, the data transmitted via the transport protocol utilizes Vegas Transmission Control Protocol (TCP) as the congestion control algorithm, where it uses increasing in delay round trip time (RTT) as a signal of network congestion. However, this congestion control algorithm will attempt to fill network buffer, which causes an increase in (RTT) determined by Vegas, thereby reducing the congestion window, and making the transmission slower, Therefore Vegas has not been widely adopted on the Internet. In this paper, an improved algorithm called TCP Vegas-A is proposed consist of two parts: the first part is sending the congestion window used by the algorithm for congestion avoidance along with the TTL (Time To Live) mechanism that limits the lifetime of a packet in the network. While the second part of the algorithm is the priority-based packet sending strategy, and jitter is used as a congestion signal indication. The combination of the two is expected to improve the efficiency of congestion detection. A mathematical model is established, and the analysis of the model shows that the algorithm has better effects on controlling congestion and improving the network throughput, decreasing packet loss rate and increasing network utilization, the simulation is done using NS-2 network simulation platform environment and the results support the theoretical analysis.
The difference between the density of the gas core of microbubbles and the surrounding media causes the behavior of microbubbles contrast agents in an ultrasound field to be nonlinear and intricate. In addition, many factors affect the radial oscillations of these microbubbles. Some of these factors are related with the bubble structure and its shell material such as the initial radius of the bubble, shell thickness, viscosity of the shell material and its elasticity. Other factors are related with the incident acoustic wave such as the driving frequency and driving pressure amplitude. In this simulation study the effects of pressure and frequency as influential factors on the stability of the microbubble were studied in wide range (frequencies are extend from f<fr to f?3 fr, pressure extends from 0.05 to 1.5 MPa.), and analyzed using the bifurcation theory to visualize and characterize the effect of these factors on the microbubbles behavior. The study expounded theoretically that the generation the higher order of subharmonic oscillations is possible to result at high driving frequencies with low and appropriate driving pressures.
Computed tomography (CT) imaging is an important diagnostic tool. CT imaging facilitates the internal rendering of a scanned object by measuring the attenuation of beams of X-ray radiation. CT employs a mathematical technique of image reconstruction; those techniques are classified as; analytical and iterative. The iterative reconstruction (IR) methods have been proven to be superior over the analytical methods, but due to their prolonged reconstruction time, those methods are excluded from routine use in clinical applications. In this paper the reconstruction time of an IR algorithm is minimized through the employment of an adaptive region growing segmentation method that focuses the image reconstruction process on a specified region, thus ignoring unwanted pixels that increase the computation time. This method is tested on the iterative algebraic reconstruction technique (ART) algorithm. Some phantom images are used in this paper to demonstrate the effects of the segmentation process. The simulation results are executed using MATLAB (version R2018b) programming language, and a computer system with the following specifications: CPU core i7 (2.40 GHz) for processing. Simulation results indicate that this method will reduce the reconstruction time of the iterative algorithms, and will enhance the quality of the reconstructed image.
The present work is a numerical study of thermal performance of modified flat plate solar water collectors. Numerical simulations have been done by solving the governing equations (Continuity, Momentum and Energy) equations in the laminar regime , three dimensions by using the FLUENT software version (14.5). The effect of flow on temperature distribution of flat plate water collectors by inserting (twist strip with twist ratio (3), helical spring surrounding the solid shaft) inside riser pipes is numerically simulated and compared with solar collector without inserting device inside its riser pipes at flow rates of (100)?/h . The numerical simulation results show that the flat plate water, solar collectors with the inserted, twist strip and helical spring that’s surround the solid shaft were higher enhancement of heat transfer than without inserted devices. The useful energy in case of twist strip is (10%) higher than the case of flat plate solar collector without enhancement device. Also, the case of helical spring is increased (6.8 %) than the twist strip, and (16.2%) than collector without enhancement device for the same mass flow rate.
With the occurrence of pathological disorders in some people or aging, metabolic energy consumption begins significantly due to the weakness of the peripheral muscles and the increase in body fat with time, which aggravates the issues for this type of people, causing the rest hours extremely lengthy and consequently may produce heart or arterial diseases and elevate the mortality rate. Regarding the significance of the matter, this study examines a number of previous researches that featured several approaches to energy calculation and strategies for lowering energy consumption through the use of various external assistance devices, such as exosuits or exoskeletons, to assist people in carrying out their everyday tasks. And additionally discussed musculoskeletal simulation employs a variety of programs, especially OpenSim, which enables users to build models of musculoskeletal structures and produce dynamic movement simulations. According to the research findings, exoskeletons and other assistive technology can successfully lower the cost of metabolic energy to varying extents, depending on the device's weight, placement within the body, and whether it is active, semi-active, or inactive. In the future, the work to design and simulate a semi-active torsional ankle-foot exoskeleton with a specialized mechanism aimed to minimize metabolic energy.
The aim of this work is to use Fiber Bragg Grating (FBG) to detect the breast cancer at its earliest stages based on the Photoacoustic (PA) hybrid technique. The fiber Bragg gratings sensitivity to acoustic wave, effect of grating length, effect of grating refractive index modification, and ultrasonic frequency on the wavelength sensitivity and intensity sensitivity of the ultrasonic sensor (FBG) for ultrasonic waves were investigated using a simulation programs. A wavelength for the photoacoustic (PA) excitation laser was chosen with respect to a high absorption by the tumor and with low absorption to the surrounding tissue (normal tissue); for higher contrast absorption between them. Fiber Bragg can be used as a sensor to detect the acoustic wave emitted from the tumor (depending on the photoacoustic principle). In this study, k-wave a MATLAB toolbox was used to simulate photoacoustic wave which is detected with fiber Bragg grating simulation, using Optisystem program. The acoustic wave was transferred to FBG by using Optisystem-MTLAB communication programs to detect tumors.
An orthogonal chaotic vectors based differential chaos shift keying (OCV-DCSK) digital communication system is presented. In this system the data transmission rates are increased by sending M bits in the same frame without needing for synchronization and channel state information since it use the benefit of non-coherent modulation of the DCSK and the orthogonality of chaotic vectors in the same scenario as QCSK system but instead of using Hilbert transform to create two orthogonal signals in QCSK, Gram Schmidt process is used to create M orthogonal chaotic signals from the M non-orthogonal chaotic signal. In the proposed system the analytical expression for OCV-DCSK are derived in AWGN and multipath fading channels. The simulation results show that the derived analytical expression have matched the Monte-Carlo simulation of the proposed system. Furthermore, comparison between orthogonal chaotic vectors and non-orthogonal, that are generated either as different initial conditions with the same chaotic generator or as different types of chaotic maps, reveals its superior BER performance in multipath fading channel.
Recently microwave photonic filter (MPF) have a great interest due to their advantages which include low loss, wide bandwidth tunability, reconfigurability, and no electromagnetic interference. This paper presented a comprehensive optical transmission analysis of a reflective-type microring resonator (R-MRR) using coupled mode theory, and design guidelines for MPF through two cascaded R-MRR using COMSOL software simulation results. The design was implemented on silicon-on-insulator (SOI) platform-based MPF which exhibits wide bandwidth tunability and reconfigurability by adjusting the coupling coefficient in the two coupling regions. In this structure, a grating coupler (GC) reflector is introduced to the drop port of MRR. The analysis and simulation results were confirmed by utilizing a GC reflector and Mach-Zehender Interferometer (MZI). The results of the proposed MPF at laser light input of (1.55*10^6- m) wavelength showed the bandwidth and center frequency are adjusted from 0.3 to 6 GHz and 13 to 54.8 GHz, respectively, with a high rejection ratio reaching 70 dB. Overall, the structure represents a significant step towards designing the MPFs, which show perfect flexibility and have numerous applications in such fields as radar, sensor, and wireless communications.
Mobile robots use simultaneous localization and mapping (SLAM) techniques for generating maps of unknown environments through navigating its. In this work, firstly SLAM technique was considered based on extended Kalman filter (EKF) which it was implemented and evaluated at unknown environments with different number of landmarks to estimate mobile robot’s position and build a map for navigated environment at the same time. Then, the detectable landmarks will play an important role in controlling the overall navigation process as well EKF-SLAM technique’s performance. After that, three intelligent optimization algorithms are proposed to enhance the performance of the EKF-SLAM trajectory for the mobile robot, these algorithms are: particle swarm optimization (PSO), chaotic particle swarm optimization (CPSO) and genetic optimization (GA). MATLAB simulation results show that CPSO algorithm outperforms PSO and GA algorithms in terms of minimizing the mean square error (MSE1) with increasing the number of landmarks, where MSE1 is the mean square error of EKF-SLAM according to the actual trajectory. The simulation results show also the performance of EKF-SLAM trajectory is better than the performance of the Odometry trajectory and becomes best with using intelligent optimization algorithms.
The improvement in solar chimneys' thermal performance and thermal behavior that can be achieved by adding metal foam has been tested in computational work. The flow and heat transfer governing equations for solar chimney models were solved using computational fluid dynamics (CFD). It was solved using the control volume numerical method in ANSYS FLUENT 14.5. It is used to construct a finite volume modeling technique for solving the governing equations and the radiation heat transfer equations. With standard flat absorber plates, the results showed that heat transmission was increased by the inclusion of metal foam (10 PPI), leading to an increase in air velocity at the solar chimney of around 13.3%. The highest average air velocity with 10 PPI drops by 54.4% as the height of the absorber plate changes from 5 cm to 25 cm respectively.
The hydraulic characteristics of dams can be predicted with high precision and reliability of physical and numerical models depending on accurate hydraulic data. The model is operated and simulated to get a more efficient, optimized utilization of the dam. This research included a comprehensive overview and literature examination of the Makhool Dam which is considered one of the most important dams under construction in Iraq. Previous studies of the dam focused on different topics in the operation of the dam and analyses of its properties, part of which focused on the dam ability to manage flood and how it works best with other dams in critical times, and another part studied the properties of the stilling basin, velocity in the dam reservoir, pressure, seepage and other characteristics that affect the operating the dam. Despite this research and the variety of topics discussed, there is no well-established research on the operation of the bottom and emergency spillway of the dam by using computational fluid dynamics (CFD) simulation software. CFD is considered an essential tech because it has an important influence in determining the hydraulic properties of a spillway and studying its effectiveness under different operating conditions. Because the spillway is an important element in the dam body, the research highlighted the necessity of performing a simulation using appropriate CFD software for this part. This research has also reviewed previous research on CFD software and their ability to simulate previously constructed or under-construction dams to analysis of its hydraulic properties.
Cone-beam computed tomography (CBCT) is an indispensable method that reconstructs three dimensional (3D) images. CBCT employs a mathematical technique of reconstruction, which reveals the anatomy of the patient’s body through the measurements of projections. The mathematical techniques employed in the reconstruction process are classified as; analytical, and iterative. The iterative reconstruction methods have been proven to be superior over the analytical methods, but due to their prolonged reconstruction time those methods are excluded from routine use in clinical applications. The aim of this research is to accelerate the iterative methods by performing the reconstruction process using a graphical processing unit (GPU). This method is tested on two iterative-reconstruction algorithms (IR), the algebraic reconstruction technique (ART), and the multiplicative algebraic reconstruction technique (MART). The results are compared against the traditional ART, and MART. A 3D test head phantom image is used in this research to demonstrate results of the proposed method on the reconstruction algorithms. The simulation results are executed using MATLAB (version R2018b) programming language and computer system with the following specifications: CPU core i7 (2.40 GHz) for the processing, with a NIVDIA GEFORCE GPU. Experimental results indicate, that this method reduces the reconstruction time for the iterative algorithms.
thetic socket, is due to its fiber strength and hardness, and low cost, but there are other more important things which must be considered than these specifications which are1the health1and safety. In this research fiberglass is replaced with monofilament fiber in order to be safe to on makers and users of this socket. In this paper two models of lamination manufacturing have been made and compared in terms of mechanical properties and fatigue life. The first is available and consists of: (4 perlon, 2 fiberglass and 4 perlon), The second is proposed lamination which consists of: (4 perlon, 1 cotton, 1 monofilament and 4 perlon). Simulations were conducted on the made socket made of two types of lamination by using ANSYS 14.5 to show the distribution of stresses, the amount of deformation and less safety factor for both cases. The results show an increase of 42% in the Young's modulus and a decrease in tensile stress and yield stress by 10.8% and 46% respectivel, As for the stress endurance it witnessed an increase of 140%.The simulation results show a decrease in the deformation by 40.7% and an increase in the minimum value of the safety factor of 0.323 to 1.05.
The assessment of prosthetic aortic valves through echocardiography, a pivotal noninvasive tool, encounters challenges, with discordant findings compared to invasive measurements, particularly in transvalvular gradients. To address these complexities, this comprehensive review article explores diverse methodologies and modalities for assessing prosthetic aortic valve performance. As these life-saving devices advance in complexity, the demand for precise and innovative assessment techniques intensifies. This journey through established and emerging modalities aims to inform clinical practice, foster experimental innovation, and enhance patient care in the realm of aortic valve prosthetic assessment. Ultimately, a profound understanding of the hemodynamic milieu engendered by aortic prosthetic valves serves as the cornerstone for optimizing valve design and clinical utility. The primary objective of this comprehensive review is to elucidate, with utmost precision, the multifaceted methodologies employed in the investigation and evaluation of mechanical prosthetic aortic valve.
This paper provides a theoretical framework for analysis of consensus algorithm for multi-agent networked systems considering the role of directed information flow. Improvement of the performance of the implemented consensus algorithm has been achieved by using Particle Swarm Optimization (PSO). Concepts of information consensus in networks and methods of convergence are applied as well. Our analysis framework is based on tools algebraic Graph Theory (GT). Simulation of multi-agent system and the performance of a consensus algorithm have been discussed. Acceleration the network while approaching the required goal has been accomplished and elimination of undesired swing that appears during the acceleration was proved.
Improvements in the thermo-physical properties of Phase Change Materials (PCM) caused by nanoparticle dissipation are critical for a wide range of technologies. The current study describes numerically the investigation of the charging and discharging process of paraffin wax dispersed with different concentrations (1%, 3%, 5%, 7%, and 10% ) of Alumina nanoparticles (Al2O3), in a Single Thermal Energy Storage (STES) system. For this study, a time-dependent, two-dimensional simulation of the solidification and melting process was performed numerically for different velocities. The study is realized using the CFD ANSYS FLUENT software package (Version 18) that employs the phase-change phenomenon using the enthalpy technique. The results show that adding alumina nanoparticles to paraffin wax reduces the melting and solidification process, and raising nanoparticle concentration accelerated the melting and solidification process even more when compared to pure paraffin wax. The greatest improvement was obtained with the maximum concentration of nanoparticles with total time saving between (12% - 11.76% ) in the charging process and between ( 15.71% - 19.60% ) in the discharging process depending on velocity. Furthermore, other important findings were that the presence of nanoparticles makes a little effect in the early stages of the solidification and melting processes, but as time passes, the rate of solidification and melting rises. Comparison with previous works gave good agreement of about 34%.
The goal of this paper is to present a study of tuning the Proportional-Integral-Derivative (PID) controller for control the position of a DC motor by using the Particle Swarm Optimization (PSO) technique as well as the Ziegler & Nichols (ZN) technique. The conventional Ziegler & Nichols (ZN) method for tuning the PID controller gives a big overshoot and large settling time, so for this reason a modern control approach such as particle swarm optimization (PSO) is used to overcome this disadvantage. In this work, a third order system is considered to be the model of a DC motor. Four types of performance indices are used when using the particle swarm optimization technique. These indices are ISE, IAE, ITAE and ITSE. Also study the effect of each one of these performance indices by obtaining the percentage overshoot and settling time when a unit step input is applied to a DC motor. A comparison is made between the two methods for tuning the parameters of PID controller for control the position of a DC motor is considered. The first one is tuning the controller by using the Particle Swarm Optimization technique where the second is tuning by using the Ziegler & Nichols method. The proposed PID parameters adjustment by the Particle Swarm Optimization technique showed better results than the Ziegler & Nichols’ method. The obtained simulation results showed good validity of the proposed method. MATLAB programming and Simulink were adopted in this work.
The security level and robustness of memristive image encryption techniques depend on the order and dynamics complexity of the memristive system. The grid multi-double-scroll (GMDS) chaotic system (CS) offers extremely rich dynamics but the implementation of high-order chaos needs large computation time. To overcome this limitation, researchers have proposed the use of muti-lower-order CSs to assist the encryption process individually. This scenario may reduce the security level since the non-friendly user may attack each involved CS independently. This paper proposes an effective six-dimensional (6D) memristive chaotic system constructed by combining 5D, 5D, and 7D GMDS chaotic systems. Each of the six chaotic sequences is generated from three sequences corresponding to two or three of the basic CSs. The combined CS shares the same total key parameters (initial values and design parameters associated with the three basic CSs) and this leads to a key space of 22392, the highest among the reported image encryption techniques. The combined CS is used to assist the operation of a proposed color image encryption scheme consisting of four sequential stages that perform compressive sensing, scrambling, DNA encoding, and diffusion, respectively. Simulation results validate the feasibility and robust security of the proposed encryption scheme.
This paper proposes a design for a network connected over public networks using Virtual Private Network (VPN) technique. The network consists of five sites; center server and four customer service sites, each site consists of a number of LANs depending on the user services requirements. This work aims to measure the effect of VPN on the performance of a network. Four approaches are implements: Network design without using VPN, network design using VPN with centralized servers, network design using VPN with distributed servers, and network design using server load balance.The OPNET and BOSON simulation results show higher response time for packet transmission due to effect of VPN tunneling. The concurrent activation of application execution is used as a solution to the delay problem of the initial timing period while the application proceeds. The results dealing with QoS are E-mail, FTP, voice services traffic and IP traffic dropped. The VPN Tunnels is in the range of (0.01 to 0.02) sec.; along with this simulator there are four VPN tunnels in the network. Also, a special server’s load balance is used to manage distribution of the server processing load across all other network servers to achieve the best response
The study aims to evaluate the current flood carrying capacity and its change after some cross sections developments for the 110 km reach of Tigris River and Kmait flood escape system. This reach extends from Ali Al-Gharbi station to Amarah Barrage station. The model is calibrated by using set of data at the Ali Al-Garbi gaging station, that includes flow varied between 790 to 470 m3/s during April 2019. Manning’s n coefficient value of (0.03) is selected as it has the minimum least-squares root difference of (0.148) between the measured and estimated water levels. The results show that the current capacity of Kmait flood escape and this Tigris River reach are 280 m3/s and 1100 m3/s, respectively. According to the study of strategic for water and land resources in Iraq, 2014, scenarios are conducted for some cross sections development to improve the capacity of the reach to 2750 m3/s. Results of applied development show that Tigris River can safely accommodate a flood wave of 2750 m3/s when modifying the cross-sections in different locations, and raising the banks level in three locations, 0+00, 79+00 and 95+00km. Earthworks volume of development of the reach is 247603200 million m³, with the total cost of 490 billion IQD.
Transfer function characteristics of a DC machine are used in this paper to estimate speed and torque in four quadrant operation modes. Estimation speed and torque control based on a DC machine transfer function is implemented by measuring the DC chopper instantaneous average output voltage and current. MATLAB\SIMULINK is used to implement the DC drive circuit in the forward and reverse motoring and regenerative modes, respectively. The DC drive system is simulated at different speed and load torque values in steady state and dynamic operating conditions. Simulation results demonstrate success of the sensorless and PI controller systems, which gives satisfactory agreements between the estimated, actual and reference speed and torque values.
Laser annealing represents a powerful method for tailoring the properties of silver nanofilms on quartz substrates, offering advantages in terms of precision, scalability, and functionalization. Continued research efforts are expected to deepen our understanding and broaden the applications of this promising technology in diverse fields. In this work, laser annealing of silver nanofilms deposited on quartz substrates was performed and investigated. RF CO2 laser of variable power in the range 1–20 W with beam quality of 1.1 was used to anneal silver nanofilms. AFM analysis emphasized that nanocrystal sizes of 60 nm were obtained for silver nanofilms. Furthermore, the optimum absorbance peak occurred at about 449 nm for smaller film thickness. Thermal simulation and analysis of the annealing process were also conducted using COMSOL Multiphysics software. It was observed that optimal temperature of 729 K was achieved when 10 W laser power and 2 mm/s scanning speed were used to anneal 20 nm silver film thickness. Design of expert analysis was also used to better understand the laser annealing process of silver nanofilms since convolution of several process parameters affect the process output.
The 3-D numerical simulations of the thermal collectors in solar heating systems were conducted to simulate the conventional solar heating system, multipurpose solar water heater (MPSWH), and multipurpose solar air heater (MPSAH). The commercial computational fluid dynamics (CFD), AVL Fire ver. 2009.2 was used to solve and investigate the temperature distributions in the absorber plate and riser tube of both solar water and air heater during summer and winter seasons. The RNG k -turbulence model was employed for this CFD study. The present paper was to provide a good understanding of thermal performance for the solar collector at different operating conditions. The experimental setup and physical data of Venkatesh, R. and Christraj, W. [15] were employed as geometric parameters and initial boundary conditions to model and to validate the predicted numerical values. Comparing to the values of temperatures for the conventional SWH and SAH, the predicted results of the MPSWH and the MPSAH showed a good improvement on the thermal performance. These enhancements on the temperature may have been due to the new design adopted in the multipurpose solar heating systems by using riser tubes and headers to the original design of the thermal systems. Additionally, the thermal performance of solar collectors increases with increasing the mass flow rates and thermal conductivity of absorber plate. For validation aspect, the predicted results of all cases examined showed a good agreement against the measured results in terms of temperature distribution levels and thermal efficiencies.
This study simulates a free-space optical communication system that uses optical beams with varying responses to atmospheric disturbances to secure transmitted data. Atmospheric turbulence was modeled with high accuracy to replicate real-world conditions closely. Non-diffracting beams were generated and used to represent optical beams and compared in two scenarios, conventional data transmission, and optifusion data protection. This approach facilitated a comprehensive analysis of the transmission environment and the effectiveness of optifusion, identifying the most suitable non-diffracting beam types for secure data propagation. By analyzing the values of key performance metrics of the selected non-diffracting beams across different weather conditions and long propagation distances, the study demonstrated the simulation system's reliability and the optifusion method's effectiveness in enhancing data security. The results showed that non-diffracting beams resist atmospheric turbulences strongly, emphasizing their potential for secure, long-range free-space optical communications.
This work involved two major parts: the first one is the experimental part which included treatment of scoliosis deformity by manufacturing thoracolumbosacral orthosis, measuring the cobb angle of deformity, measuring the gait cycle data and walk path for both legs and suggesting a composite material to improve the mechanical properties of the orthosis and finally the interface pressure between trunk and orthosis is measured for twelve points covering of the total TLSO surface area by using f-socket devise. The second part of this study is the numerical simulation part during which the stresses are calculated using Ansys software for calculating stresses due to interface pressure loading boundary condition. The result shows no deference in gait cycle phases but the clear difference noted in walking path due to deviate center of mass, maximum pressure recorded left thoracic region with 900KPa due to correct spinal deformity while the minimum pressure recorded at right chest with l40KPa because of it is tissue region and Maximum value of stress was recorded at the left thoracic region with 2.81MPa due to Maximum interface pressure at this point.
The fifth generation (5G) and beyond mobile networks support increasing number of users with increasing bit rate per users. This has encouraged researchers to propose coherent digital subcarrier multiplexing (SCM) point-to-multipoint (P2MP) architectures to reduce the cost and complexity of optical transport networks, particularly in the metro aggregation scenario. However, coherent optical receiver is relatively costly and complexity compared with a direct-detection (DD) counterpart due to the use of a synchronized local laser. This paper addresses design issues and performance investigation of intensity modulation/direct-detection (IM/DD) P2MP optical networks. P2MP architectures are designed using digital RF multisubcarrier (MSC) waveform embedded on the intensity of continuous-wave (CW) laser beside direct-detection scheme. The design covers C- and O-band operation using a wavelength-division multiplexing (WDM) architecture. Further single- and double-polarization (SP and DP) versions are reported for each type of the networks. All the architectures are built in Optisystem version 15 environment and simulated for different network parameters, under the assumption of 25 Gbps per subcarrier data rate. The main performance measures are maximum route reach and bit rate-distance product (BDP). The simulation results indicate that DD networks can replaced the coherent counterpart when number of subcarriers per optical channel is 4. Further, the O-band P2MP networks offer high values of maximum reach and BDP than C-band counterparts.
Prosthetic is an artificial tool that replaces part of the human frame absent because of ailment, damage, or distortion. The current activities in Iraq draw interest to the upper limb discipline because of the growth in variety of amputees and. It is necessary to do extensive researches in this subject to help lessen the struggling of patients. This paper describes the design and development of low-cost prosthesis for people with transradial amputations. The presented design involves a hand with five fingers moving by means of a gear box mechanism. The design of this artificial hand allows five degrees of freedom(5DOF), one degree of freedom for each finger. The artificial hand works by an actuation system (6V) Polou motor with gear ratio equal to 50:1 due to its compactness and cheapness. The designed hand was manufactured by a 3D printing process using polylacticacid material (PLA). Some experimental were accomplished using the designed hand for gripping objects. Initially the EMG signal was recorded when the muscle contracted in one second, two seconds, three seconds. The synthetic hand was able to produce range of gesture and grasping moves separately just like the actual hand by using KNN classification which are complete hand Pinch, fist, and jack chuck. The simulation of the fingers movements was achieved using ANSYS software to analysis the movement (pinch, fist, and jack chuck), obtain bested of stress influencer at each finger, and maximum deformation at each movement.
This paper proposes the design and simulation of Interval Type-2 Fuzzy Logic Control using MATLAB/Simulink to control the position of the bucket of the backhoe excavator robot during digging operations. In order to reach accurate position responses with minimum overshoot and minimum steady state error, Ant Colony Optimization (ACO) algorithm is used to tune the gains of the position and force parts for the force-position controllers to obtain the best position responses. The joints are actuated by the electro-hydraulic actuators. The force-position control incorporating two-Mamdani type-Proportional-Derivative-Interval Type-2 Fuzzy Logic Controllers for position control and 3-Proportional-Derivative Controllers for force control. The nonlinearity and uncertainty in the model that inherit in the electro hydraulic actuator system are also studied. The nonlinearity includes oil leakage and frictions in the joints. The friction model is represented as a Modified LuGre friction model in actuators. The excavator robot joints are subjected to Coulomb, viscous and stribeck friction. The uncertainty is represented by the variation of bulk modulus. It can be shown from the results that the ACO obtain the best gains of the controllers which enhances the position responses within the range of (19, 23 %) compared with the controllers tuned manually.
Algebraic reconstruction technique (ART) is iterative reconstruction algorithm using for reconstructing the two dimension (2D) and three dimension (3D) images. In this research different algorithms of ART were used to reconstruction : (simple ART, Simultaneous ART, and Multiplicative ART) for reconstruction 3D image using multi slice scanner in cone beam geometry. To perform the time reconstruction of ART algorithms, use the Maximum-Likelihood Expectation Maximization (ML-EM) algorithm to fast ART algorithm. Multi slice Computed Tomography CT scanner newly discovered and used widely in the medical field for diagnosis and radiographic to its benefit from the speed of scanner and quality of image reconstruction comparing with single slice scanner. In simulation result the Multiplicative ART (MART) algorithm with suitable relaxation parameter
In this work, for ultra-wideband (UWB) applications, a passive filter antenna with edge chamfering is investigated in this paper. The performance of an optimized UWB antenna design that achieves an advanced fractional impedance bandwidth of 102% is confirmed by simulation and experimentation. The performance of the antenna is improved by integrating a lowpass filter (LPF) into the fed line, which suppresses high-frequency radiation with a central frequency of 3.5 GHz (WiMAX), the UWB antenna has been transformed into a narrowband antenna, offering a 43.7% fractional bandwidth that spans the frequency range from 2.7 GHz to 3.9 GHz. A stepped impedance transmission line and an extended fractal H-shaped structure integrated in the microstrip feedline make up the filtering network. Using CST Microwave Studio (CST MWS), key performance parameters such as the radiation patterns, efficiency, gain, and reflection coefficient (S11) were examined. In its prototype, the antenna reduces its size by 5% and is made on a FR4 substrate with a permittivity coefficient of 4.3 and a loss tangent of 0.02. A maximum gain of 1.7 dBi and a peak efficiency of 78% at the center frequency were verified experimentally. The center frequency was verified experimentally. The tiny antenna, which measures 0.30λ₀ × 0.37λ₀ × 0.008λ₀, performs well and is appropriate for UWB applications. The design makes a significant addition to the realm of UWB technology by incorporating elements that improve its ability to adapt.
This paper presents an investigation to the performance of quantized direct-sequence spread spectrum system (DSSS) in mobile wireless communications systems. To obtain a real world value (RWV), the DSSS received signal is quantized to different levels of fixed-point values. These modes of quantization are evaluated by calculating BER under different channels environments (AWGN, Rayleigh, and Rician multipath fading). The effect of range of the represented values, the number precision and increasing in quantization noise on the performance of quantized DS in mobile wireless communications is also investigated. Based on simulation results, it is observed that quantized direct-sequence offers a trade-off between complexity and noise rejection compared to non-quantized DSSS and making a good representation of the digitized signals to implement the required DSSS in mobile wireless communications.
In recent decades, many factors have emerged in the building design field, as the technology development after the industrial revolution has left many environmental problems affecting building environments and turning them into unhealthy ones. Also, the issues of consuming natural resources required innovative and modern solutions to address, which needed the guidance and focus of researchers, engineers, and many other relevant disciplines to find the best treatments to solve them. One of the essential treatments was using advanced smart technology to solve the environmental problems of buildings, such as providing thermal comfort and reducing energy consumption. The concept of adaptive smart envelopes is one of this manifestation of advanced technology in the field of building design characterized by interaction and adaptation to the surrounding environment through the application of many technologies which it works to improve its environmental efficiency. The research aim was to simulate the changes in the building environment, which is treated by covering the building with an adaptive smart envelope by using the Rhinoceros Grasshopper programme.
The transportation cost problem of solid waste presents the biggest part of the budget allocated by municipalities for SWM. So, there is no comprehensive plan to address transport routes optimization problems in SWM that including the transfer of solid waste from transfer stations to final landfill sites. Therefore, the aim of the study finding a scientific method to solve the transportation problem of solid waste transport suitable Baghdad city that tries to find feasible solutions that ensure reducing total transport costs and leads to an effective solid waste management system. In this research, a new methodology has been developed to select the optimal transport routs of SWM in Baghdad city which involves determining the best-supposed scenario. the proposed methodology includes integration of Global Positioning System (GPS) technologies with Network Analysis model (NA). Therefore, this work provides an advanced framework of decision-makers for analysis and simulation of the optimal transport routs problem related to SWM. Applying these modeling tools to select the scenario that can provide economic benefits by minimizing travel time, travel distance and reduction of total transportation costs. The Results of work implementation show that all solutions that include current state S1 and suggested scenarios have been evaluated. The scenarios generated include (S2, S3) by applying the proposed technique for analyzed and identified the optimal routes. The solutions of scenario S2, specified with two landfill sites while scenarios S3 specified with four landfill sites. Finally, this work shows the Scenario S3 is the best scenario of the solution, that include applied GPS and Network Analysis for four landfill sites.
In this paper, a hiding encrypted message using pseudo random number generator and sequential encoding is proposed. This algorithm can provide better security of hiding information in image. The main emphasis in mine results will be on visual image quality and also the peak signal to noise ratio (PSNR) value which is a measure of quality of embedding. The results of statistical analyses like average difference, PSNR and MSE indicate high security and suitability of the proposed scheme. The obtained result shows the peak signal to noise ratio is 79dB. The programming language MATLAB is used for implementing the proposed algorithm.
The process of placing the brackets in their proper positions in the field of orthodontics is consider one of the main steps in orthodontic treatment. In order to achieve high accuracy placements for the brackets, many methods are available today, starting from direct and indirect methods, each of them has advantages and disadvantages regarding the accuracy and the time for patient treatment. In this study, a new mechanism is introduce with its mechanical behavior in order to reduce the time required for patient treatment and to increase the accuracy for bracket placements. The newly mechanism was designed using Solidworks CAD software with a total Virtual functionality for all of the parts of the assembly, then a simulation was carried out to find the stress distribution, deformation, and strain on the main parts of the proposed assembly. The finished design shows a high precision mechanism that is able to place brackets one by one on the teeth.
The Unified Power Flow Controller (UPFC) is a most complex power electronic device, which can simultaneously control a local bus voltage and optimize power flows in the electrical power transmission system. This paper presents the effect of installing the UPFC on the Iraqi (400 kV) grid transmission system to control the active and reactive power flow by choosing the optimal location and parameters of Unified Power Flow Controllers (UPFCs), which were specified based on the Genetic Algorithm (GA) optimization method. The objectives are improving voltage profile, reducing power losses, treating power flow in overloaded transmission lines, and reducing power generation. The steady state model of UPFC has been adopted on (400 kV) Iraq transmission lines and simulated using the MATLAB programming language. The Newton-Raphson (NR) numerical analysis method has been used for solving the load flow of the system. The practical part has been solved through Power System Simulation for Engineers (PSS\E) software Version 32.0. The Comparative results between the experimental and practical parts obtained from adopting the UPFC were too close and almost the same under different loading conditions, which are (5%, 10%, 15% and 20%) of the total load.
With the development of manufacturing techniques, the demands have increased on tools with flexible components that can produce parts with different shapes and sizes only by replacing the rigid part of these tools, since the flexible part can match the required geometry. This study is focused on effects of rubber hardness and sheet thickness on the springback developed on the produced parts. Silicone rubber with three hardness (40,60 ,80) Shore A hardness scale was used. The material of workpiece was Aluminum (3003) with three different thicknesses of (0.8,1,1.2) mm and three holding time of (0,10,20) seconds. The results demonstrate that, the springback decreases with any increase in the rubber hardness or sheet thickness. In addition, the holding time showed a significant effect only with a harder rubber.
Experiments were conducted to study the effect of quenching medium carbon steel in water-based MWCNTs nanofluids at 0.05 % wt. concentration quenchant, a large cylindrical sample with 46 mm diameter and 40 mm length made from medium carbon steel used with three K-type thermocouples with a diameter of 1.5 mm inserted in three locations for sample (center of the sample, mid-point between center and surface and 1 mm from the surface). A time-temperature reading data system was used to read temperature history during cooling stage.The same experiments were simulated using ANSYS Workbench with Thermal Transient Version 19, the cooling curves at three locations for the cylindrical steel sample calculated during quenching in MWCNTs nanofluids. Quench factor analysis was used to predict the hardness results from the calculated and measured cooling curves, and these results compared with the hardness test results conducted in the significant sample from the center to the surface. The results show excellent compatibility when compared between the hardness results from cooling curves, and it also shows a good agreement with the results of the hardness test, especially at the sample surface.
A new robust control algorithm is proposed for a class of nonlinear systems represented by a Single Link Manipulator (SLM) system. This algorithm is based on new techniques and methods in order to obtain a controller for the SLM system. First of all, the system is simplified using Variable Transformation Technique (VTT) in order to fit the analysis procedure. Then, a new idea of designing a model reference for the multiple states (n=4) system is presented to correspond the control design. Next, the Lyapunov Stability Analysis (LSA) is used to figure out a proper controller that can compensate the stability and the performance of the SLM system. After that, the Most Valuable Player Algorithm (MVPA) is applied to find the optimal parameters of the proposed controller to accomplish the optimum performance improvement. Finally, it can be concluded that the proposed control algorithm has improved the stability and the performance of the SLM system. In addition, the simulation results show the remarkable effects of the proposed nonlinear controller on the SLM system.
The paper describes a design and simulation of a Supervisory Control And Data Acquisition (SCADA) system to control oil pipeline and depot plant. The aim of the process is to control oil transportation through a shared pipeline and to minimize products contamination. The study attempts to fulfill an optimal sequence of batches of refined products to satisfy the customer demands in term of: volume , maximum flow rate, optimizing the total operational cost, and reducing products contamination.The proposed system introduces a control algorithm to perform process control system functions and for achieving the tasks and actions in specific sequences and precedence. The control algorithm performs processing of pumping station control, sharing single oil pipeline, maintaining tanks level, and depot inventory control. This paper investigate many factors which effects the length of transmix segment, which enable to offer optimum solutions to reduce products contamination.LabVIEW software is used for performing various signals acquisition and monitoring, also for simulating and designing the control system strategy.
In this paper, models were applied to investigate the parameters that affect membrane fouling. Osmotic pressure across the membrane, salt concentration at the surface of the membrane, solute mass transfer coefficient, effective coefficient diffusion of water, and concentration polarization factor were the main parameters that calculated in this simulation. Sodium chloride was assumed the only salt existed in the feed flux. In addition, changing the applied pressure versus increasing the salt concentration in the feed flux and their effect on the water permeation coefficient was investigated. The results confirmed that concentration polarization gives a good indication about the formation of the fouling layer at the membrane surface and consequently permeate decline.
The heavy metals are considered dangerous pollutants which harm health and environment. The adsorption process is the cost effective process to get-rid of heavy metal efficiently. In this study, the adsorption bed of Nickel is simulated by using COMSOL Multiphysics to find the effect of different operating parameters namely; flow rate, temperature and pollutant concentration on adsorption bed efficiency. The modeling of non-isothermal adsorption bed based on experimental isotherms kinetic of previous work is developed too. The results showed that the optimal conditions to generate maximum removal efficiency of heavy metal were at 50?C inlet temperature, 0.1 M inlet concentration, and 80 ml/min flow rate to achieve removal values higher than 50 % of long operation period time.
The heat exchanger is a device used to transfer heat energy between two fluids, hot and cold. In this work, an output feedback adaptive sliding mode controller is designed to control the temperature of the outlet cold water for plate heat exchanger. The discontinuous gain value of the sliding mode controller is adapted according to a certain adaptation law, where the only information required is the measurement of the outlet cold temperature. A sliding mode differentiator was design to estimate time derivative of outlet hot water temperature. Two constraints which imposed on the volumetric flow rate of the hot water (control input) were considered within the rules of the proposed adaptation law in this work. These are the control input is positive only and has a maximum value. For constructing the sliding variable, the outlet hot water temperature and its time derivative are required. The maximum allowable desired outlet cold water has been estimated as function of heat exchanger parameters and maximum control input. The simulation results demonstrate the performance of the proposed adaptive sliding mode control where the outlet cold water was forced to follow desired temperature equal to . Additionally, the robustness of the proposed controller was tested for the case where the cold inlet temperature is not constant. The results reveal the robustness of the proposed controller.
This paper presents a numerical investigation to study the effect of variations in displacement history sequence and magnitude on cyclic response of RC tapered (haunched) beams (RCHBs).Five simply supported RCHBs (four haunched and one prismatic) were selected from experimental work carried out by Aranda et al. The selected variables included were five loading history types. The first part of this study focused to verify the finite element analysis with selected experimental work and the second part of this study focused too studying the effect of varying in loading history to the response of RCHBs. The finite element code Abaqus was used in the modeling. The adopted cyclic simulation performance of the selected beams using the plastic- damage model for concrete developed by Lubliner and Lee & Fenves. The constitutive model of plain concrete describing the uniaxial compression response under cyclic loading proposed by Thorenfeldt, and the uniaxial tension response follows the softening law proposed by Hordijk was used in the modeling. Menegotto-Pinto model was used to simulate the steel response. Model verification has shown A good agreement to the selected experimental work. The variations in loading history will decrease the ultimate load and corresponding deflection with increase in the number of cycles at ultimate load.
The hydrodynamics of stirred tanks and bubble breakup are crucial in gas-liquid flows, yet this system has not been well characterized for different operating conditions. In this work, the numerical method was used to investigate the hydrodynamics of six- flat blades impeller (Rushton turbine) and the results were employed to understand the bubble breakup behavior in the stirred tank. Simulation results of predicted flow pattern, power number, and the distribution of turbulence energy generated were performed with COMSOL Multiphysics. Numerical results showed good agreement with the experimental literature. The effect of rotational speed on bubble breakup behavior, such as breakage probability, the average number of daughter bubbles, and the breakage time was investigated using the high-speed imaging method. The main finding is that the breakage process occurs in the high energy area of high turbulence intensity, which is located within a distance equal to the blade width of a radius of (15-35 mm). The breakage probability (Bp) was found to be increased by 12.61 percent for a mother bubble of 4 mm at 340 rpm, with an average fragmentation of up to 22 fragments. Furthermore, the bubble breakage time was found to decrease with increasing impeller rotational speed, with an average value of 19.8 ms.