×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerGypsum soil is classified as problematic because it contains gypsum, a soluble substance in the presence of water. Therefore, it is recommended that it be improved before construction. This research examines the effect of clayey soils on enhancing the properties of gypseous soils. Two soil samples, designated as Soil 1 (with a gypsum concentration of 35.4%) and Soil 2 (with a gypsum content of 12.3%), were obtained from Al Najaf City, Iraq, and subjected to laboratory testing. The study investigates the use of cost-effective, locally available clayey soil to improve the engineering characteristics of gypseous soils, thereby mitigating the adverse effects of wetting. The experimental program encompassed a compaction, compressibility, and shear strength test. To assess the impact of clayey additives, gypseous soil was treated with varying percentages of clayey soil content (5% and 10%), and tests were conducted on both treated and untreated gypseous soil samples. The results indicated that using 10% clayey additives could decrease the collapse potential by 55% and 39% for Soil 1 and Soil 2, respectively. Additionally, the clayey additives significantly affected cohesion, with an enhancement percentage of 625% and 1315% under soaking conditions at 10% clayey additives for Soil 1 and Soil 2, respectively.
Gypseous soils are usually stiff when they are dry especially because of the cementation of soil particles by gypsum, but great loss in strength and sudden increase in compressibility occur when these soils are fully or partially saturated. The dissolution of the cementing gypsum causes high softening of soil. The problem becomes more complicated when water flows through the gypseous soil causing leaching and movement of gypsum. This study examines the improvement of gypseous soil properties using the Silicone oil to minimize the effect of moisture on these soils. This study was conducted on artificial gypseous soil (mixture of 30% Silber sand & 70 % Pure Gypsum) treated with silicone oil in different percentages. The reason for use the silicone oil as an additive to study the gypseous soil properties is due to the leakages of oil products from oil refinery in north of Iraq build on gypseous soil, this oil products infiltrate to the foundation soil of the refinery building facilities. _x000D_ The results showed that the Silicone oil is a good material to modify the basic properties of the gypseous soil of collapsibility and shear strength, which are the main problems of this soil and retained the soil by an appropriate amount of the cohesion suitable for carrying the loads from the structure.
There is very close relation between the pile capacity and surrounding soil conditions . In cohesionless soil the pile effected on surround soil by compact loose ,cohesionless deposits through a combination of pile volume displacement and driving vibrations .the pile foundation usually designed to exceed the weak soil to the firm deposit .in this study we shall try to improve the weak soil surround the pile and observe the effect of improvement on pile capacity for driven pile._x000D_ The improvement suggested in this study is compacting for surrounding soil . for this purpose we prepare testing program by selection two types of sand soil one as the origin soil and the other as improving soil (soil will be compacted and replace surround pile model) . pile model prepared for this purpose is consist of reinforcement steel bar covered with cement mortar , 50 kN automatic electromechanical compression machine was used for testing load- settlement test on pile model. The Testing procedure includes changing the diameter of soil compacted around pile model and execute the load settlement test and compare the results.
Expansive soil poses significant challenges for civil engineers worldwide since it seriously affects the structures built upon it. This soil has a very active group of minerals called montmorillonite, which is responsible for the significant volume change it exhibits. For a number of years, chemical additives have been utilized to stabilize soil, with various levels of success. Soil stabilization has involved the use of a variety of additives, including cement, lime, polymers, salts, and combinations of these. However, lime is very often used for expansive soil stabilization as it improves the soil's mechanical properties. The effects of adding three percentages of lime (3%, 6%, and 9%) to expansive soil to improve its engineering properties are investigated through several tests. The laboratory tests consist of standard compaction, sieve analysis, atterberg limits, hydrometer, California bearing ratio, consolidation test, swelling potential, and specific gravity. The test results displayed that the plasticity index, liquid limit, swelling potential, and maximum dry density, specific gravity decreased using (3%, 6%, and 9%) lime. In contrast, the plastic limit, and optimum moisture content increased using (3%, 6%, and 9%) lime. The California bearing ratio is increased from (12.13% to 14.65%) by adding (9% L). The swelling index and compression index are decreased from (0.070 to 0.030) and from (0.581 to 0.193) respectively by adding (9% L). The swelling percentage is reduced from (18.77% to 6.03%) by adding (9% L).
Many researchers have applied several experiments and research studies by developing criteria's design of drainage to improve the drainage process, and to show that the filters plays an important role to improve and maintain the drainage system from being blocked due to siltation. There are several types of filters, including granular mineral materials and organic materials, the other filter that was used is made from a special fabric material such as paper, burlap, or special fabric textile material. The objective of this study is to evaluate the performance of textile filters, and if it is desirable and suitable for Iraqi soil using statistical analysis. This study was conducted in the laboratory using sand tank model and two types of filters (graded crushed gravel and textile) with two types of soil (sandy soil and loamy soil) to compare and evaluate the hydraulic performance and the efficiency of utilizing textile filter instead of graded crushed gravel filter in drainage systems using statistical analysis methods. These statistical analysis show that there was a good agreement between measured and theoretical values of entrance resistance when using the two filters in sandy soil. On the other hand, the results showed that there was a weak performance when textile filters in were used in heavy soil (loamy soil) due to the high value of root mean square error (RMSE) and low value of agreement index (d). The results of statistical analysis show that the textile filter is desirable and suitable for Iraqi soil especially for sandy soil due to low entrance resistance of flow compared to loamy soil.
Quality control of riverbank roads is a vital part of the road construction and maintenance process and aims to ensure infrastructure quality, safety, and sustainability. This requires adherence to technical standards, constant auditing, and regular maintenance to maintain the condition of the roads and avoid potential problems. The first step in the quality control of roads is to test the efficiency of the subgrade soil. A geotechnical investigation of subgrade soil under river bank roads is carried out to evaluate the engineering properties of the soil and determine the soil’s ability to bear the loads resulting from vehicle movement and road traffic. This investigation includes analyzing soil samples and laboratory tests to determine soil properties and determine any improvements the soil needs to bear the loads. Soil samples were collected from Al-Kadhimiya Corniche Street. It was dried and subjected to laboratory tests, the soil in this study is classified as poorly graded sand (SP), GS 2.589, the shear strength parameters an internal friction angle of 33 degrees and cohesion of 0.5 kN/m2, and the results of the compaction test indicated that the optimal moisture content was 8.1%, with a maximum dry density was 18.24 kN/m3, CBR 26.04%, and chemical tests (SO3 0.222, pH 8.55, T.SS 0.891, CL 0.085). Software FAARFIELD was used to check pavement design, the thickness design was executed utilising a subgrade CBR value of 26.04%. The subgrade pavement thickness was determined to be 304mm in total. The results agree with the actual design of Al-Kadhimiya Corniche Street, which was recently maintained during the field investigation in 2023.
Field compaction equipment used for fine grained soil usually applies a kneading action or vibration that produces shear forces which also reshape soil particles arrangement. A state that might not be completely simulated by laboratory Proctor tests. This study aims at investigating the significance of using the newer modified Texas superpave gyratory compactor (SGC) to simulate field compaction of fine grained soil due to itsability to apply loads in different anglesgenerating shear forces on the compacted soilspecimens. Two types of soil (A-4) and (A-7-6)were compacted using standard Proctor,modified Proctor and (SGC). The results werecompared to dry field densities of the same soilin order to evaluate the most representative test.It was found that maximum dry densities of soiltype (A-4) obtained using (SGC) under (200kPa) and (600 kPa) were lower by (2.07%) andhigher by (1.35%) than the maximum drydensities obtained using standard and modifiedProctor tests respectively. It was also found thatmaximum dry densities of soil type (A-7-6)obtained using (SGC) under (300 kPa) and (600kPa) were lower by (1.02%) and higher by(1.23%) than the maximum dry densitiesobtained using standard and modified Proctortests respectively. The aforementionedconfinement pressure values were applied inorder to achieve dry densities similar to thatobtained by Proctor tests. When comparinglaboratory results to dry filed densities, it wasfound that (SGC) test results were slightly closerto them than Proctor tests results. Nevertheless,the difference between (SGC) and Proctor testsresults seems to be insignificant for these typesof soil compared to the higher effort needed toperform (SGC) tests.
Rigid pavement slabs are erected on a prepared subgrade or foundation layer, providing a hard and continuous surface. Transverse joints made of dowel bars connect them, and longitudinal joints made of tie bars join them longitudinally. This study is an investigation of the impact of soil strength and concrete parameters on the effectiveness of dowel bars in rigid pavements. Moreover, three parameters were examined; California Bearing Ratio (CBR), concrete compressive strength and slab thickness. The analysis was conducted using the Ever FE program and focused on several axle configurations applied to the joint. The results indicate inverse association between the pavement slab thickness and the concrete strength, under the assumption of consistent soil strength. Moreover, an assortment of reduced shear forces on the dowel bars is seen when the soil strength values increase. It indicates that soil strength has a greater impact on the shear load of dowel bars compared to the qualities of concrete. Additionally, the type of axles used and the magnitude of soil strength were shown to have a significant effect on the shear load.
Due to significant increasing in seismic activity in world during the last decades especially in Middle East region; engineers have been giving increasing attention to the design of buildings for earthquake resistance. In this study 3-D seismic behavior of piles is investigated using the finite element program PLAXIS 3D 2013. _x000D_ Piles are one of the most commonly used foundations in seismic areas where the soil is inadequate to carry the load on its own. In these seismic areas, piles often pass through (penetrate) shallow loose and/or soft soil deposits and rests on competent end bearing soils. Thus a model of soil - pile system is simulated in the finite element program._x000D_ The dynamic parameters of soil are used as input dynamic data of PLAXIS 3D program, in addition to the static properties of soil collected from soil investigation works._x000D_ The research showed the susceptibility of PLAXIS 3D program in analyzing piles with different soil conditions under earthquake action. The results also showed the importance of studying seismic behavior of soil-pile system using 3-D analysis rather than 2-D analysis because the problem is truly 3-D and should be analyzed as such.
Most researches have predicted soil erosion of cohesive riverbanks using linear (excess shear stress model) and non-linear (Wilson model) models based on two soil parameters (detachment coefficient, kd, and critical shear stress, ?c) of the linear model and two soil mechanistic parameters (mechanistic detachment parameter, b0, and threshold parameter, b1) of the non-linear model. The goal of this research was to quantify the soil erodibility parameters of Tigris Riverbanks on Nu’maniyah-Kut Barrage reach using linear and non-linear models through the model parameters at three different water contents: dry side, optimum side, and wet side of water contents. Soil samples were collected from three locations south of Baghdad city on Nu’maniyah-Kut Barrage reach of Tigris Riverbanks. Six soil samples acquired from these sites were laboratory tests achieved using a miniature version of Jet Erosion Test device (“mini” JET) to determine the erodibility parameters of both linear and non-linear models. Blaisdell solution (BL) and scour depth solution (SD) were applied to determine (kd and ?c) of linear model from JETs data. Physical soil characteristics; including bulk density, particle size distribution (sand%, silt%, and clay%), average particle size (D50), and angle of repose were reported for six samples acquired from the three sites. The results showed lower value of kd of toe in compared with bank side for some specific sites as observed for both BL and SD solutions of excess shear stress model especially at wet side of water content. No general pattern of ?c related to different water content were observed. The parameters (b0 and b1) of non-linear model have the same behavior of linear model parameters (kd and ?c), but with different magnitude related to different water contents, respectively.
Unconfined compressive strength represents an important parameter for soil investigation report test results because the values of cohesion and allowable bearing capacity can directly obtained from the relevant test especially if the clayey soil layers are found at sufficient enough depth above water table level._x000D_ This paper deals with simple comparison (based on (31) soil samples) between unconfined compressive strength (qu) obtained by using the pocket soil penetrometer tool and the unconfined compressive strength using the conventional test for the same sample penetrated by the pocket penetrometer with different soil moisture contents. Two triaxial specimens, sample type-1- with dimensions 38 X 79mm and type-2- with dimensions 33 X 79mm(diam. X height)) prepared in the libratory._x000D_ It was found that the results refers that soil pocket penetrometer readings are closed enough to the results that obtained from the unconfined compression test result with certain conditions._x000D_ The average percentage of difference between penetrometer readings and unconfined compression test result values was (1.103%) for sample type-1- and (1.53%) for sample type -2-._x000D_ The maximum moisture content for all tests samples was (27.3%) and the minimum was (14.7%) while the average moisture content was(20.9%).
Shallow foundation suffers from considerable settlement, displacement and tilting under earthquakes. This is particularly due to the shaking associated with earthquakes that lead to the generation of horizontal seismic load transferred through the soil to the foundation. Also, liquefaction could take place during the earthquake in the saturated loose sand. To alleviate the detrimental effect of earthquakes, ground improvement is required. This study examines the response of the shallow square foundation rested on loose sand soil reinforced with geogrid reinforcement when subjected to 2023 Turkey earthquake by using a shaking table system. Different number of geogrid layers are installed; (one, two, three and four), also various geogrid configurations were examined which are (straight, trapezoidal and reverse trapezoidal). The acceleration response, settlement, horizontal displacement, rotation and pore water pressure developed in the sand soil and the shallow foundation during 2023 Turkey earthquake has been examined. The settlement and the horizontal displacement, foundation rotation, acceleration and pore water pressure were measured using rope displacement transducers, tilt sensors, accelerometers and pore water transducers respectively. The results showed that the acceleration amplifies when passing through loose sand. The results also indicated that the shallow foundation experienced noticeable settlement, horizontal displacement and rotation when subjected to the seismic loads. On the other hand, the installation of geogrid proved to be effective in controlling the problems associated with earthquakes. The optimum geogrid reinforcement is occurred when three layers of geogrid placed in reverse trapezoidal configuration (3RT) since it gave the best reduction in the acceleration amplification and the highest decrease in the foundation settlement, displacement and tilting which is about (60-66) %. Nevertheless, the effectiveness of geogrid minimizes when the sand soil becomes saturated. In addition, liquefaction occurs during earthquakes especially at the shallower depths because of the decrease in the shear strength of saturated soil.
Soil’s characteristics are essential for the successful design of projects such as airports runway and flexible pavement. CBR (California Bering Ratio) is one of the significant soil characteristics for highways and airports projects. Thus, the CBR property can be used to determine the subgrade reaction of soil through correlations. Many of the soil geotechnical parameters such as compaction characteristics (Maximum Dry Density, MDD; Optimum Moisture Content, OMC), and consistency parameters (Liquid Limit, LL; Plastic Limit, PL; Plasticity Index, PI) can be in charge of changes that happen in soil CBR value. Soaked and/or non-soaked conditions of soils also affect CBR value. Hence, testing soils in a laboratory for CBR calculation is time-consuming that needs notable effort. Therefore, this study aims to generate some useful correlations for soil’s CBR with compaction and consistency parameters for 85 samples of fine-grained soils. The study trials were applied on natural soil samples of various places in Sulaimani Governorate, Northern Iraq. Statistical analysis has been carried out by using SPSS software (Version 28). Soaked CBR is counted, which is important for conditions such as rural roads that remain prone to water for few days. Based on the statistical analysis, there is a significant correlation between LL, PL, PI, MDD, and OMC with CBR as the dependent variable as a single variable equation with R2 of 0.7673, 0.5423, 0.5192, 0.6489, and 0.51, respectively. In addition, the highest value of R2 correlation was obtained between CBR value with consistency and compaction properties as a multiple regression equation with R2 of 0.82. The obtained equations for correlation purposes are successfully achieved and can be used, notably, to estimate CBR value.
Soil reinforcement techniques have been successfully used to improve the shear properties of weak soils in recent years. To improve the utilization of waste resources and promote sustainable development of infrastructure amid rapid urbanization, one potential option for reinforcement materials is human hair fibers (HHF). Because it is a natural fiber, there are risks to human and environmental health associated with the improper disposal of human hair fiber, an occurring waste product that does not decompose completely. This fabric is abundant, has a high reusability rate, and is ideal for use as a reinforcement to address waste management issues and make the most of inefficient or unnecessary manufacturing websites for long-term sustainability. The CBR test was executed on several samples with diverse fiber possibilities to evaluate the engineering properties of the randomly placed HHF in clayey soil samples using fibers whose average length was 50 mm and whose diameter ranged from 60 to 80 microns and compared the outcomes to those of unreinforced soil. The soil sample was treated with different percentages of Human Hair fiber (0%, 0.75%, 1.5%, 1.75% and 2.25%). The results showed that the value of CBR of the soil sample decrease at 0.75% of HHF and then increased up to 2.25% of HHF.
An overview of electro-osmosis (EO) and electrokinetic (EK) soil treatment methods is provided in this paper, along with their impact on pile capacity, installation, and foundation shear strength after improving the geotechnical properties of weak soils, particularly soft clays. As a result of their low shear strength, high compressibility, and poor drainage characteristics, soft clayey soils pose significant challenges in civil engineering. With EO and EK, pore water and ions are moved through the soil matrix under an applied electric field, resulting in consolidation, increased shear strength, and reduced plasticity. This review explores the fundamental principles of EO and EK, including the mechanisms of water transport, ion migration, and electrochemical reactions. It examines various electrode configurations, treatment parameters, and their influence on soil improvement. Furthermore, the paper analyzes the effects of EO treatment on pile capacity, considering both the increase in soil strength and the reduction in pore water pressure during installation. The impact on pile installation methods, such as reducing driving resistance and improving grout penetration, is also discussed. Finally, the review investigates the enhancement of foundation shear strength through improved soil properties achieved by EO/EK treatment. By synthesizing existing research, this paper aims to provide a comprehensive understanding of the potential benefits and limitations of EO and EK methods for ground improvement in soft clayey soils, offering valuable insights for future research and practical applications in geotechnical engineering.
The aim of this laboratory study is to estimate the best initial pH of purging solution for cadmium clean-up from an artificially contaminated soil using electro-kinetic cell. An efficiency enhancement scheme was employed involving pH control and injection wells as a part of the investigative program. Seven tests were performed at different pH controlled in the anode, cathode and injection wells start from 2 to 8. Sandy loam soil was contaminated with cadmium concentration equal to 2000 mg/kg and an initial moisture content equal to 30%. The duration of remediation was seven days with a potential gradient of 1.2 V/cm. The experimental results showed that the best removal efficiency was 62.8% at pH=3._x000D_ Keywords: , , , ,
This study explores the impact of adding high-density polyethylene (HDPE) and Novolac polymers to gypseous soil from Tikrit City, Iraq, to enhance its geotechnical properties. The soil contained 38% gypsum, and the polymers were added in varying proportions (1%, 3%, 6%). Both polymers improved maximum dry density, optimum moisture content, and reduced collapse potential (Ic). The collapse potential was reduced by 64%, 77.7%, and 83.2% at 1%, 3%, and 6% HDPE content, respectively. The collapse potential was reduced by 82.3%, 74.8%, and 51.9% at 1%, 3%, and 6% Novolac polymer content, respectively. In the dry conditions, the internal friction angle increased by about 22.9% and 5.7% as the HDPE content was increased by 3% and 6% respectively. Adding Novolac polymer also increased the internal friction angle by about 5.7% by the addition of 3% Novolac polymer. In soaked conditions, the best increase in internal friction angle (?) was 30% with the addition of 3% HDPE polymer. the internal friction angle increased by about 26.7% by adding 1% and 3% of Novolac polymer. The study concludes that adding HDPE and Novolac polymers can improve geotechnical properties, but their effect on CBR is complex and depends on the polymer percentage added and soil moisture state.
This research is devoted to design and implement a Supervisory Control and Data Acquisition system (SCADA) for monitoring and controlling the corrosion of a carbon steel pipe buried in soil. A smart technique equipped with a microcontroller, a collection of sensors and a communication system was applied to monitor and control the operation of an ICCP process for a carbon steel pipe. The integration of the built hardware, LabVIEW graphical programming and PC interface produces an effective SCADA system for two types of control namely: a Proportional Integral Derivative (PID) that supports a closed loop, and a traditional open loop control. Through this work, under environmental temperature of 30°C, an evaluation and comparison were done for two types of controls tested at low soil moisture (48%) and high soil moisture (80 %) to study the value of current, anode voltage, pipe to soil potential (PSP) and consumed power. The results show an decrease of 59.1% in consumed power when the moisture changes from the low to high level. It was reached that the closed loop controller PID is the best solution in terms of efficiency, reliability, fast response and power consumption.
The finite element method is one of the important methods in analyzing geotechnical engineering problems; its main advantage is the ability to apply for the materials exhibiting non-linear stress-strain behavior. In this study the finite element program PLAXIS 3D 2013 is used to study the behavior of the piles under the influence of seismic waves in saturated sandy soil and the effect of adding geogrid with the pile foundation. The program has been used to facilitate the representation of the real model, input the required soil parameters and implementation of seismic data. Seismic wave, the soil geometry and the pile dimensions were fixed in all models, while dimension and depth of the geogrid used were varied to study the influence of different depth and dimension in reducing the pile displacements and the pore water pressure of soil. The results show that The reduction in settlement ratio (the difference between settlement of pile without and with using geogrid to the settlement without using geogrid) for ( ×L/2), (L×L) and (2L×2L) are 10.6%, 17% and 21.3% respectively. And the settlement ratio for geogrid at depths 8.33% and 12.5% of pile length are 9.6% and 17% respectively.
The axial capacity and pile transference of loads under static loading have both been well reported, but further research is needed to understand the dynamic lateral responses. The pile load imposed during an earthquake may increase, but the soil’s ability to support it may fall as a side effect of the vibration leading to more settlement. The key objective of this work is to identify what led to the substantial lateral destruction of the piles during the seismic event due to the kinematic effects. These failures were related to discontinuities in the subsoil as a result of sudden changes in soil strength due to shaking. The kinematic stresses exerted in a single pipe pile constructed in two sand layers under two different situations (dry and saturated states) are investigated in this study using numerical modeling. The bending moments were higher in the saturated sand soil than in the dry one which may be attributed to liquefaction. Generally, the acceleration increased through the loose layer (from bottom to top), and then significantly settled within the dense layer. It could be shown that using this modeling, one can estimate how a pile foundation will behave under "kinematic" loading driven by earthquakes. Therefore, the design and installation of drilled aluminum or steel piles in sand soil could make use of these present observations.
This paper aim to study the effects of earth reinforcement on the stresses generated within a semicircular cross-section tunnel lining buried in sandy soil due to surface loading. The effect of position and number of reinforcement layers was studied. Also, the relative density of soil was investigated. The depth of soil above the tunnel crown was fixed to be three times the tunnel radius. Two relative densities for soil were used, 55.3% and 73.3%. One layer of reinforcement that was used located at distance equal to the radius or two times the radius above tunnel crown. Also, two layers of reinforcement were located at distance equal to radius and two times radius above the tunnel crown. The results show that the use of earth reinforcement will reduce the stresses generated in the tunnel lining due to application of surface loading.
The aim of this work is to investigate the effect of soil corrosion on the critical buckling load of circular columns made of 2014-T4 aluminum alloy. In this work, 24 specimens were used and buried in the soil for 120 days. The samples divided into two groups (12 columns with corrosion before shot penning (SP) and ultrasonic impact treatment (UIT), and 12 columns with corrosion after combined surface treatments (SP+UIT)). The experimental1results revealed1that the corrosion negatively1affects the mechanical properties1of the material, and the1reduction percentage (R%) for1ultimate tensile strength (UTS) and1yield strength (YS) was (1.95% and 4.57%) respectively. After combined surface treatments (SP+UIT) for the corroded columns, the ultimate1tensile strength (UTS) and yield1strength (YS) were improved with (2.42%, and 2.87%) respectively. Perry-Robertson, Rankine, and ANSYS were used to estimate the critical buckling load (Pcr) and compare it with the experimental results. Rankine and Perry's formulas have been achieved a good agreement with the experimental without and with (1.5) factor of safety respectively. While ANSYS gave satisfactory prediction with a safety factor of (2.2, and 2.7) and (1.9, and 2.7) for long and intermediate columns before and after (SP+UIP) respectively.
This paper is intended to study the effect of using upstream and downstream sheet pile in double soil layer on the seepage, uplift pressure exit gradient at toe of hydraulic structure using computer program SEEP/W software._x000D_ Depended on the software program tests were carried out with three different value of each following parameter: upstream sheet pile depth, downstream sheet pile depth, permeability for first and second soil layer, depth of first and second soil layer, with using constant upstream head and distance between the two sheet pile. For each test the quantity of seepage, exit gradient and uplift pressure at toe of hydraulics structure were determined. Based on the results of these runs an empirical equations developed to determine the quantity of seepage, uplift pressure and exit gradient at toe of hydraulic structure by using SPSS software. Also, Verify the SEEP/W results and the suggested equations with artificial neural network (ANN). The verification show difference less than 5% , 2% and 6% for exit gradient, discharge and uplift pressure respectively at toe of hydraulic structure.
Most of the soils suffered from significant geotechnical problems dependent on factors like the type of soil, soil composition and mineralogy. Specifically, the problems related to mechanical and physical properties of soils. Several studies have been used to mitigate the adverse effects of soils through using either additive conventional materials such as cement, lime or these soils blending with produced material and chemical materials. This paper focuses on stabilizing or improving different soils using sustainable materials. These materials provided environmental and economic benefits while mitigating a health hazard, storage problems, and a potential pollution source. They can be classified according to these sources into four groups: industrial waste (by-products), agriculture waste, domestic waste and mineral waste. According to the results of this review, compaction characteristics, California bearing ratio and unconfined compressive strength have been studied and discussed in this paper.
The evaluation of the behavior of bridge piers with soils surrounding them during earthquakes became necessary in Iraq especially after the influential earthquakes hit middle and south of Iraq during the last few years. A three dimensional finite element model for the bridge substructure and soil surrounding the bored piles with the actual dimensions and actual properties corresponding to "Sheikh Sa'ad Bridge" in Sheikh Sa'ad district at Wasit Governorate 37km south east of Kut city is presented. The model loaded with earthquake ground motion applied as lateral forces at one side of piles cap. The Earthquake hit 11 km from Ali-Al Gharbee in Maysan Province in 2012 with a magnitude of ML = 4.9 is used as the input ground motion. The response of the pier was investigated and the performance of piles and the soil surrounding them was examined. Then these typical piers and surrounding soils were checked weather they can bear the stresses induced due to these earthquake forces. From this work, it was found that typical piers used in bridges in Iraq can sustain earthquakes up to those with a magnitude of ML = 6.8 maximum.
In this study a numerical examples and solutions has been obtained by using three system of beam resting on elastic foundation (BOEF) which was adopted previously by three different engineering software. The first part of this paper was related to verify the model of (BOEF) by using ETABS2015 by make a comparison with previous results by determination the maximum settlements at the mid of span which show a good agreement between ETABS2015 and other results, where the total differences was vary from 2.13 % to 3.27%. . The second part of this study was highlighted on the settlement of BOEF with different parametric study (beam thickness, soil subgrade reaction(KS) and the load location), case (1) was selected for this goal. In this paper it is found that the differential settlement along the beam are decrease as increasing in the beam stiffness in addition to possibility to obtain uplift (positive settlement ) for some type of changing in the load location specially for higher thick beam . It was noticed that the settlement are increased significantly as reducing in the (KS). Finally this study show a different form of deflection by combination two of parametric study.
Driven piles have often been used in many civil structures to provide structural loading support. However, the unavoidable vibrations induced by pile driving processes may cause varying degrees of damage to adjacent structures. This research presents experimental studies to investigate the transmitted vibrations induced by impact of pile driving on vicinity piles. In the experimental work, a small scale model was tested in a sand box (steel container 1 × 1.5 × 0.8 m) with pile driving hammer device to install the impact pile in sand soil by dropping weights (1, 2, 3, 4 and 5 kg) for different heights of falling (4, 8, 12, 16 and 20 cm). The peak particle velocity was measured at a head of the vicinity piles by vibration meter device. In this study, several piles on different distances away from the vibration source were studied. The experimental results indicate that the peak particle velocity for vibrations emitted with impact pile driving is increased with increasing the energy and the penetration depth of pile driving for all vicinity piles and it can be decreased without change in the driving energy by decreasing the weight of hammer and increasing the height of falling hammer. Vibration intensities are attenuated with increasing surface distance from the pile driving and the peak particle velocity decreased uniformly with surface distance from the pile driving for piles. Also, through laboratory model representation and evaluation of the results obtained in the laboratory, the empirical relations which were determined based on the scaled-distance concept, are appropriate and give results very close and can be relied upon to represent the transmission of vibration resulting from the impact of pile driving to nearby piles.
In this paper, a dynamic analysis has been carried out on zoned earthdam subjected to earthquake excitation in which pore water pressure, effective stresses and displacements are calculated. The finite element method is used and the computer program Geo-Studio is adopted in the analysis through its sub-programs SEEP/W and QUAKE/W. A case study is considered to be Khassa Chai dam which is located on Khassa Chai river north of Iraq and consists of zoned embankment with a total length of 3.34 km. The selected earthquake for the analysis is El-Centro earthquake with a period of 10 sec and different amplitudes of acceleration. The time of the analysis is taken as 600 sec. with a time step (?t = 0.05 sec.) to investigate the behavior of the soil for a period of time after the earthquake has stopped, a free vibration period is included in the analysis. It was concluded that the value of pore water pressure generated at the base of the core is greater than that in the upper parts of dam. The horizontal and vertical effective stresses continue to decrease during the period of analysis 600 sec. which indicates that the soil continues to weaken during this period, the horizontal displacement increases with depth of the point from the crest and the largest horizontal displacement will be at the base of the dam at time 60 sec and There is attenuation of the acceleration to some degree depending on the amplitude of the input horizontal acceleration. The maximum horizontal displacement decreases by about 37%, 45% and 49% when using a horizontal drain 2 m thick at the downstream under a peak acceleration of 0.05g, 0.1g and 0.2g, respectively.
Bio-cement built on microbial induced carbonate precipitation MICP, be able to consolidate the loose grains and can applied for soil reinforcement. In this study, the performing of an ureolytic Sporosarcina Pasteurii for sand stabilization was estimated. The S. Pasteurii Could effectively consolidates sand particles through urea hydrolysis and the successive production of calcite. The bio improved sands had relative great compressive strength after 60 days exposure to bacterial cells injections cycles. The compressive strength of bio stabilized sands was reliant on the utilized cell concentrations and density of urea and CaCl2. High bacteria cell masses decreased the compressive strength. The optimal density of cell, was OD600 0.5, when cost and performance were taken into account. The study shows that bio cementation of sand built on microbial induced carbonate precipitation (MICP) has ability for the reduction of sand permeability through pore clogging with precipitated carbonate.
Artificial neural networks (ANN) as new techniques employed for the development of predictive models to estimate the needed parameters in geotechnical engineering to be used for comparison with laboratory and field tests and consequently reduce the cost, time, and effort. Flexible computing techniques are using an alternative statistical tool to analyze and evaluate experimental data from 102 consolidation tests on a variety of undisturbed soils from Ramadi city. The regression equations are developed to estimate the compression index and the compression ratio from index data. Multi-Layer Perceptron (MLP) network model is used to calculate compression index and a compression ratio of soils and comparing with the multiple linear regression statistical model MLR. It is found that the MLP showed a higher performance than MLR in predicting Cc and Cr and model accuracy between 0.81 to 16 percent. This will provide a good method for minimizing the potential inconsistency of correlations.
This research deals with the extent to which corrosion affects the behavior of buckling for 6061-T4 aluminum alloy under increasing compressive dynamic loads. Two types of columns, long, and intermediate were used.1% of the length column is the allowable lateral deflection. This is called the critical buckling of the columns. For the purpose of calculating the critical deflection, a digital dial gauge was used and set at a distance of 0.7 of column length from the fixed end condition for the column. The experimental analysis revealed that the corrosion time negatively affects the mechanical properties of materials such as the corroded specimens of 60 days (The least time to observe the corrosion of aluminum in the soil) which have approximately 2.7 % reduction in ultimate strength compared with the non-corroded specimen. Increasing the corrosion time reduces the critical load such as the maximum reduction will be 4.24% in critical buckling load for 60 days’ corrosion time. The results obtained were experimentally compared with the theoretical formulas of the Perry-Robertson and Euler-Johnson formula with the results of the ANSYS. It was found that the Perry-Robertson formula has a good agreement with the experimental results with a safety factor of 1.2, while the Euler-Johnson formula agreed with the experimental results taking a safety factor of 1.5. The ANSYS results showed a good agreement between the measured and calculated values by taking 1.1 factor of safety.