×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe toxicity of permanent implants is the main concern. The release of ions from the substrate leads to toxicity. Because of how the human body works biologically, the toxicity of corrosion compounds is a byproduct of wear and fretting debris. aimed to improve the corrosion resistance of a 316L stainless steel substrate. Bio ceramic Nano-hydroxyapatite (HA) was coated using the Electrophoretic Deposition (EPD) technique. Stainless steel has good mechanical properties and high compatibility, but it suffers from body fluid attack due to its chloride content, which can penetrate the passivation layer, resulting in the release of chromium and nickel ions. Tissues and organs are damaged by the ions and debris that are released. To address this problem, it was coated with bioceramic using the EPD method. Suspensions of various powders—hydroxyapatite, magnesium oxide, zinc oxide, and the composite—were prepared and coated by electrophoretic deposition. The coated samples were dried at room temperature to ensure a homogeneous coating structure. The zeta potential test for magnesium oxide and hydroxyapatite suspensions was positive, while zinc oxide and complex suspensions were negative. One of the important parameters for achieving electrolyte and implant balance is the open circuit potential (OCP). A substantial change towards a more noble direction (less negative) was seen in the OCP-coated (316 L) alloy, suggesting excellent thermodynamic stability. Tafel extrapolation analysis was used to obtain the corrosion potential (Ecorr) and corrosion current density (Icorr) values of composite-coated stainless steel 316L, which are generally derived from the polarization curve. The findings that are in line with the MgO, HA, and ZnO coatings show a significant decrease in corrosion current (Icorr), an increase in corrosion potential (Ecorr), and a decrease in corrosion rate from (4.386 × 10-¹ mm/y) Stainless Steel 316 L to (1.417 × 10-² mm/y) MgO Coated and (1.222 × 10-³ mm/y) (65%MgO+25%ZnO+10%HA coated).
Zinc oxide nano particles is one of the best choices for ultraviolet protection due to its special properties. In this research, the UV-protection ability of sol gel-derived thin ZnO films on cotton fabrics was investigated. Various polymers have been used as adhesives to bind the nano-oxide with the surface of the treated fabric. Scanning electron microscopy and UV spectroscopy were carried out to study the properties of the treated fabrics. The results showed that the diameters of the synthesis zinc oxide particles - (68.81, 41.76 and 44.6 nm) with (PVA, PVP and CMC) respectively- were of the nanostructure, and the smallest diameter of the particles was produced with polyvinylpyrrolidone as adhesive. Using a spectrophotometer showed a decrease in the transmittance of the studied samples compared with the raw untreated sample of about 23%.
In this work, environmentally friendly zinc oxide nanoparticles was produced using sustainable green technology. With several loading amounts, such as 5%, 10%, 50%, and 100%, the banana peel extract was utilized as a capping agent. This was followed by calcinations at 400 ºC for 3 h in a muffle furnace. To evaluate the physical and chemical change of the synthesized nanoparticles, XRD, FTIR, UV-VIS and SEM/EDAX was used. The characterization results reveald that the all the green synthesized ZnO NPs samples strongly supports the well-crystallinity with high phase purity. The average crystallite size of the prepared samples was calculated using Debye-Scherer's formula and the results shows that with an increase in extract amount, the average crystallite size was shrinking. The FTIR result verified the successful chemical reaction between zinc salt and banana peel extract. The UV-VIS results showed the effect of size quantisization phenomena at 100% extract adding. Finally, the SEM images for all the prepared samples confirm the spherical shape.