Articles in This Issue
Abstract
Due to the instability and irregular of national electric power supplied to residence sector in Iraq for long term history, attracted researchers interest to strive for solutions, and associated challenge dry and very hot summer season in Iraq on air conditioning application, A test room full size prototype was constructed in Baghdad, its size 33.5m3, the room is built from very good thermal insulation Autoclave Aerated Concrete AAC with white panted Concrete roof, test room is exposed to solar radiation during entire day, thermal energy shifted by time using thermal energy storage TES containing PCM, PCM is soft paraffin its phase inversion temperature (29 to 27)°C, thermal energy was shifted from night timing by cooling down TES (Discharging PCM) to peak time 11:00 am to 02:00 pm, the testes were carried out over entire summer season April to October, the results showed thermal energy can shift to by any quantity and time based on mass of PCM and enthalpy, electrical energy saved at peak time 52.5% of total power spent over season 2.7KW/day, Only 27% of electric energy utilized to discharge PCM during night, about 43% of heat lose is sourced from exposed roof, melting and solidification of PCM temperature must be within indoor comfort range 23 to 28 ?C to release or absorb the latent heat 41kJ/kg.
Abstract
Bio-cement built on microbial induced carbonate precipitation MICP, be able to consolidate the loose grains and can applied for soil reinforcement. In this study, the performing of an ureolytic Sporosarcina Pasteurii for sand stabilization was estimated. The S. Pasteurii Could effectively consolidates sand particles through urea hydrolysis and the successive production of calcite. The bio improved sands had relative great compressive strength after 60 days exposure to bacterial cells injections cycles. The compressive strength of bio stabilized sands was reliant on the utilized cell concentrations and density of urea and CaCl2. High bacteria cell masses decreased the compressive strength. The optimal density of cell, was OD600 0.5, when cost and performance were taken into account. The study shows that bio cementation of sand built on microbial induced carbonate precipitation (MICP) has ability for the reduction of sand permeability through pore clogging with precipitated carbonate.
Abstract
Recently, considering polymer composite in manufacturing of mechanical parts can be caused a fatigue failure due to the very long time of exposure to cyclic loading and may at environmental temperatures higher than their glass transition temperature; therefore, in this paper, a comprehensive investigation for bending fatigue behavior at room and elevated temperatures equal to 60 °C, 70°C, and 80 °C will be done. Rotating bending test machine was manufactured for this purpose supplied with a connected furnace to perform fatigue tests at elevated temperatures. The obtained results appeared that the increase in applied stress and temperature caused a clear reduction in fatigue life; also the addition of carbon nanotubes enhanced the fatigue life at different temperatures by 183%, 205%, 218%, and 240%, respectively while the addition of short carbon fibers improved fatigue life by 324%, 351%, 387%, and 415%, respectively. As well as, Polyamide 6,6/carbon fiber composite appeared fatigue limit at temperatures equal to 20°C and 60°C and stresses approximately equal to 55 MPa and 38 MPa respectively.
Abstract
Regaining the activities of daily living after stroke and spinal cord injury requires repetitive and intensive tasks, meaning that rehabilitation therapy should be treated with a long duration. Thus, the need for rehabilitation devices based home is of most importance to increase the rehabilitation process and provide more comfortability for patients. This paper focuses on implementing and construction of a three degree of freedom (DOF) (flexion/extension, adduction/abduction, and pronation/supination), low cost, lightweight, and portable robotic exoskeleton for wrist-forearm rehabilitation. SolidWorks software program and 3D printer technology are used to model and construct the proposed robotic exoskeleton structure. In addition, the anthropometric parameters of the normal human lower arm are considered for this exoskeleton to provide a range of motion (ROM) and velocity for the links, joints, which matches with the anatomical structure of human and also to avoid the excesses motions over the normal range. The exoskeleton is constructed by a 3D printer utilizing polylactic acid (PLA) plastic material. The proposed implementing structure of the robotic exoskeleton shows comfortable, lightweight, simple and economic as well.
Abstract
The indemnification of uncertainty and disturbance which is added to non-linear systems by an Integral Sliding Mode Controller (ISMC) design. the key target of this paper is designing a sturdy controller to observe the performance of a 2-link robot. The nonlinearity in mechanical systems is a shared issue that the researchers are facing in formulating control systems for it. The best solution to this problem is a design Sliding Mode Controller (SMC) for controlling a nonlinear system. In the current paper, 2-link robot is studied which suffering from disturbances and parameter uncertainty and coulomb friction as additional to friction inertia of the system for each link. firstly, Classical Sliding Mode Controller (CSMC) is designed and then Integral Sliding Mode Controller (ISMC). As known, CSMC includes two phases: reaching phase and sliding phase. SMC is suffering from the known phenomenon as "chattering" which is supposed as a critical case and unsuitable characteristic. chattering is described as a curvy movement span the switching surface. In the current study, the chattering is attenuated by employing a saturation function alternative of a sign function. Although SMC can be considered as a good way of controlling nonlinear systems. Where it continues to suffer from the long settling time as undesired features. ISMC is a good method can be employed for reducing the settling time and controlling a nonlinear system. ISMC is easy, robust execution and supposes as an active and strong technique. The most significant advantage in ISMC designing, the reaching phase is canceled that considered a major part of designing classical SMC. The 2 link Robot system was used for proving the performance of CSMC and ISMC algorithms. The outcomes received from the simulations utilizing the ISMC and CSMC which fulfilled asymptotic stability for the system. In comparative between CSMC and ISMC. ISMC is better than CSMC in the good performance of tracking the desired position with less time. Finally, MATLAB2019a software package has relied upon this work.
Abstract
In the last two decades, underwater acoustic sensor networks have begun to be used for commercial and non-commercial purposes. In this paper, the focus will be on improving the monitoring performance system of oil pipelines. Linear wireless sensor networks are a model of underwater applications for which many solutions have been developed through several research studies in previous years for data collection research. In underwater environments, there are certain inherent limitations, like large propagation delays, high error rate, limited bandwidth capacity, and communication with short-range. Many deployment algorithms and routing algorithms have been used in this field. In this work a new hierarchical network model proposed with improvement to Smart Redirect or Jump algorithm (SRJ). This improved algorithm is used in an underwater linear wireless sensor network for data transfer to reduce the complexity in routing algorithm for relay nodes which boost delay in communication. This work is implemented using OMNeT++ and MATLAB based on their integration. The results obtained based on throughput, energy consumption, and end to the end delay.
Abstract
In this paper, the efficiency of six different types of corrosion inhibitors used in Basrah drinking water tanks was assessed using a potentiostatic test method. The mechanism of adsorption of silicate and phosphate inhibitors in AISI 316 stainless steel surfaces and the effects of different water components in inhibitors are discussed in detail. The values of corrosion rate obtained from the Potentiostatic test showed that the protection against corrosion in the presence of inhibitors is better compared to the case of absence of inhibitors. The results of the six types of corrosion inhibitors tested showed that the inhibitory efficacy is higher below the temperatures 45oC, but when raise the temperature above 45oC the inhibitory efficiency becomes to decrease. Also, the test results indicated that the corrosion inhibitor involves silicate products provided more inhibited efficiency compared to the phosphate inhibitor alone or used the combined silicate/phosphate corrosion inhibitor. The inspection of the surface of the tested samples using optical methods shows that the pitting corrosion is demonstrated on the specimen surfaces after testing with or without inhibitors.
Abstract
Three-dimensional reconstruction of real objects comprises capturing the appearance and the shape for these objects and determining the three-dimensional coordinates for their profiles. This reconstruction process can be accomplished either by using active or passive techniques. In this paper, a new fusion method is proposed for 3D reconstruction. This method exploits the advantages of both stereo-based passive and laser-based active techniques and overcomes their limitations to improve the performance of 3D reconstruction. With this method, a hybrid laser-based structured light scanning system is designed and implemented. This system captures the required information using passive and active techniques and uses the proposed fusion method for 3D reconstruction. The performance of the proposed method and its scanning system were experimentally evaluated. The evaluation results show high reconstruction performance for the proposed fusion method over the traditional 3D reconstruction techniques. The results also show the effectiveness of the hybrid laser scanning system and its ability to scan and reconstruct the shape and the appearance for real objects using the proposed fusion method.
Abstract
Most of the soils suffered from significant geotechnical problems dependent on factors like the type of soil, soil composition and mineralogy. Specifically, the problems related to mechanical and physical properties of soils. Several studies have been used to mitigate the adverse effects of soils through using either additive conventional materials such as cement, lime or these soils blending with produced material and chemical materials. This paper focuses on stabilizing or improving different soils using sustainable materials. These materials provided environmental and economic benefits while mitigating a health hazard, storage problems, and a potential pollution source. They can be classified according to these sources into four groups: industrial waste (by-products), agriculture waste, domestic waste and mineral waste. According to the results of this review, compaction characteristics, California bearing ratio and unconfined compressive strength have been studied and discussed in this paper.
Abstract
Numerical analysis of the performance of reinforced concrete (RC) deep beam subjected to static and fixed-point pulsating loading at the midpoint has been investigated. Three-dimensional nonlinear finite element model using the Strut and Tie approach was adopted. The damage level under the influence of the applied fixed pulsating loading is higher than the static applied loading, hence early crack was observed because of the stepwise loading in the form of vibration. Although the Strut and Tie approach gave a good estimation of the resistance capacity of the beam, the beam undergo high shear damage when subjected to these two types of loading. Material strength properties, applied loadings and cross-sections adopted are some of the factors that affect the performance of the deep beam.
Abstract
In this vast world after an earthquake lessons are learned; many strategies have been considered in order to achieve a proper seismic strength capacity.The aim of this paper is studying the seismic behavior of a typical reinforced concrete bridge pier in Iraq and implementing a proper technique of strengthening in order to fix any damage that had happened.Structure of a full scale three-dimensional finite element model was used in order to simulate a reinforced concrete pier via the computer software ABAQUS/CAE 2017 using concrete plasticity damage model (CDP).Under the action of Halabja earthquake, which was recorded at city of Halabja in Iraq on 12 November 2017, the behavior of model was traced, analyzed and the resulted damages were managed.The finite element analysis results indicated that the proposed configuration of carbon fiber reinforced polymers laminates substantially increases the lateral load strength and deformation capacity of the bridge pier